Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
Hello,
I have problems using nrFgo Studio with my J-link programmer. The "nrf5x Programming" section is greyed out when the j-link is connected to the PC and the MCU....
I am working on a client to collect data from a continuous glucose monitor. I see that the CGM Service has been part of the SDK for some time. But there is no matching client...
Hello
I have nRF52840-DK and also a nRF52840 Dongle with me and i have installed SEGGER Embedded Studio with "nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71" SDK downloaded...
Hi--
On dev kit PCA100056, SoftDevice s140, SDK 15.3, in project ble_app_uart_pca10056_s140, we are trying to operate the UART TX/RX characteristic with outgoing payloads...
Hi All,
I'm very new to this Bluetooth mesh technology. Currently I'm referring to client/server switch example.
Without making any changes in the firmware I compiled...
I am seing odd time strings from AT+CCLK... Like: "+CCLK: "15/02/01,00:00:08"\r\nOK\r\n"
I think it is required that AT+CCLK responds error until it has gotten network time...
Hi!
I work at Lund university and I'm preparing a upcoming course project course. The course is about prototyping and PCB design. I want to use the nrf9160 as a example...
I get FDS_SUCCESS after I do fds_write(&desc, &m_dummy_record).
But when I do rc_read = fds_record_find(FILE_ID, REC_KEY, &desc, &tok); I get an error code rc_read = FDS_ERR_NOT_FOUND;...
Hi all,
I am trying to develop an Android app to connect to a nrf52832 running the ble_app_uart example. Previously I was using the Android-nRF-UART codes as a starting...
Hello
I have nRF52840-DK and also a nRF52840 Dongle with me and i have installed SEGGER Embedded Studio with "nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71" SDK downloaded...
I'm having a frustrating time trying to enable UARTE1 to stream fast ADC results to a terminal.
I believe I have edited sdk_config.h correctly, but looking at nrf_serial...
In continue to https://devzone.nordicsemi.com/support/233777 We tested the demo for some days, it works. But last week it stoped on open socket with error -47. At the same...
HI,
I have successfully installed Wireshark and nRF Sniffer on a Windows 64-bit machine. Now I am trying to duplicate the process on a windows 32-bit machine without any...
I want to flash in dfu sample.
*nrf_dfu_flash_erase *nrf_dfu_flash_store Called nrf_dfu_flash_init (true) to execute the above function. Since true is set in the argument...
Hi,
In order to be absolutely sure, can you confirm me that the nRF9160 module can be configured with following interfaces running simultaneously, all with dedicated GPIO...
