Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am trying to flash the program into my custom board. and i am successfully flash the program into custom board. I have flashed the blinky code in y custom board. it's works...
Hi everyone,
I would like to know in the ble_app_uart_pca10040 where the Bluetooth antenna is connected on pin planner to be able to change it.
Thanks you for helping...
Hello there,
I have a question related to the ADC of the nRF52832.
I am using it in single-ended mode, 10-bit resolution, 1/5 gain, internal reference 0.6V.
Thus...
Hello,
I am wondering what this "Low Power Event" is.
I am looking through the document but I can't find the place that explains this.
Can somebody point me to the place...
Hi, I followed the tutorial to Debug with Real Time Terminal on Keil.
fatal error: file sdk_config.h not found.
I have followed the tutorial as precisely as I can, maybe...
hi，there
I met an error in Nordic_HRM examples. The error code is GATT_CONN_TERMINATE_LOCAL_HOST.After the connection is established, you can see the service that has...
Good morning everyone,
it is the stupidest question ever, but I was unable to find an answer neither here nor on the segger forums or documentation.
This forum seems...
It's NRF52832 and NRF52810.
The BLE connection process is to establish a physical connection first and then discover the service to obtain the characteristic word information...
Hi,
For my application, I would like to have multiple watchdog timers. I am measuring several sensors (I want one short-term watchdog timer to be fed in this loop, pause...
I am new with nrf52 DK . I was trying to work with SPI code example given in the nordic example folder but its not working . I am trying to transfer the accellero/ gyro data...
I am using SDK 15.0 with the Nordic NRF52840 development board. I wrote my own custom bootloader using CDC ACM as the transport. I am using app_usbd_cdc_acm_read_any to read...
Hello All,
Is there any already available example of OLED display interfacing with nRF52DK, pca10040, SDK 14.1 in Segger Embedded studio?
I am working on a project...
Hi，
I want to measure the time of two signals to calculate the speed and sent the data with BLE. I find the SD effect the GPIOTE_interrupt sometimes, when I try to use GPIOTE...
I an trying to locate and download some programming examples. For instance the BLE Blinky application
ble_app_blinky_c says it is in the EXAMPLE FOLDER, no matter where...
