I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
I enter to bootloader via my app by UART command:
err_code = sd_power_gpregret_clr(0, 0xffffffff);
APP_ERROR_CHECK(err_code);
err_code = sd_power_gpregret_set(0, 0xB1...
I know nothing about bluetooth
like ble_app_uart , uart to where?how to use this uart?
like ble_app_alert_notification, alert? beep? vibrator?
any tutorial of develop...
Hi. I am connecting to and establishing a bond between my Android phone and the nRF52832 board using the s132 SoftDevice. I'm in a situation where the Android phone has a...
Hello,
I have the following setup:
A Raspberry Pi 3 B and a nRF52840 Development Kit acting as a Border Router as described here
Another nRF52840 Development Kit...
Hi there,
I'm trying to run the beacon s130 pca20006 example on a custom board. There are 2 main differences between the pca20006 and my board:
There is a 32 Mhz...
Hi,
it seems there was lately a new IC revision release of the nRF52840.
Is the nRF52840 IC Revision Engineering B 100% pin compatible to Engineering A, i.e. pinning...
Please excuse my basic question but I'm new to this - I am needing to have data collected from probe/sensor, which would be in a device, sent every hour to an android app...
Hello,
We plan to switch between two sets of UART pins for factory testing. One set will talk to an IC in our design and the other to a USB port through FTDI. Since simultaneous...
Hello,
We'd like to connect 50 bluetooth 5 devices (nRF52840) to a Receiver (made of multiple centrals nRF52840) with a long range (PHY 250kbps, conn interval 50ms, no...
We are evaluating the nRF5 SDK 13.0 to upgrade our projects from v12.0 and it looks like it has a bug related to the FDS functionality.
I managed to reproduce it on the...
Hi friends,
I am doing a project in NRF24le1 using RF communication with multiple nodes with a host using star topology.
Could you suggest a Protocol that supports connecting...
Hi,
to what impedance shall the BT antenna be matched?
Copying from the datasheet:
A matching network is needed between the RF pin ANT and the antenna, to match the...
Requests for the FW:
Add characteristic to access general GPIO pins in analog and digital form.
extension of the existing MOS_1-4 access, PIN read/write under the...
Hi,
We use nrf51 SDK v9. I found there are two SER_MAX_CONNECTIONS defined both in app_ble_gap_sec_keys.h and ser_config.h. Their values are different. One is referred...
Hello,
I have a problem when I try to use cheaper Android phones to communicate with our 52832 chip.
I can discover the peripheral and then connect, but when I device...
