At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hi,
We are doing DFU updates through a nrf51422 dongle (data passing from UART to BLE), using our own code, based on the multilink central example.
The DFU peripherals...
Hi, I'm have a question :
If i download s120 or s130 softdevice, which SDK version i need to download ?
Which version is compatible with my nrf51822xaa ?
The reason is...
Our BLE hardware is designed to send data at 50 Hz speed continuously using nrf51822.
It worked well with APP with Android 4.3 and some Android 5.0/6.0 ,we can receive data...
Hi,
I'm getting familiar with my nRF52 DK (PCA 10040).
I stumbled on something when I was doing an application that toggles LED1 on every TIMER0 event (200ms). Here...
Hi,
Id like to understand the FDS state after flashing the device. Im trying to check if the record exists then I use it, otherwise I write a valid info into the record....
Hello All
Could you please guide me. i want implement BLE with SPI interface...if i sent any command via mobile Bluetooth..then NRF51 DK should receive the Command and...
I have already changed the define NRF52, NRF52832_XXAA,BOARD_PCA10040 to NRF51,NRF51822 and BOARD_PCA10001 and adjusted the ROM and RAM areas as below.
But there...
ERROR OCCURS WHEN TESTING UART nus service on a nrf52832 custom board UART APP SHOWS LIKE THIS device doesn't support UART WHEN I TRYING TO CONNECT WITH MY DEVICE. PLZZ H...
Hi Nordic Team,
In one of our application, we need to interface BT HCI chip with Host MCU(Cortex M4 based). Below are the application profiles we need support for:
...
I am having trouble using GPIO P0_9 and P0_10 as GPIO pins. These are the pins designated as NFC1 and NFC2.
I am using the following sample code:
#include <stdbool.h...
Can a peripheral device know when the client made a scan response request? I want to use scan response as a form of acknowledgment so the peripheral device knows that the...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
It looks like there is a new version of nRF Sniffer for the nRF52, but it doesn't seem to be formally released, although it seems to be 6 months old. Is it expected to be...
Hi,
i was just wondering as we dont need the high clock rate whether its possible to run the nrf52832 with less than 64 Mhz by replacing the 32 mhz crystal with a different...
