This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi,
I'm wondering if I'm missing something. I've been creating a bluetooth mesh light with hue, saturation, brightness, on/off, etc. models. However, my model_handler.c...
I have an app that uses the Nordic IOS-DFU-LIBRARY to drive the OTA DFU process with an Adafruit nrf52840 Feather running the Adafruit bootloader. I have the library setup...
Hello,
I am currently working with the Sniffer API provided in the extcap folder of the nRF Sniffer for Bluetooth LE package. However, I am unable to find recent documentation...
Dear Nordic support team,
We are using the SDK v2.6.1 to build targets for nRF52840 chips, and are using multiple configurations defined in a CMakePreset.json file.
It...
Hello,
I am trying to implement littlefs in my external flash memory. I am using nrf52832 and try to implement the littlefs sample code.
When I am trying to enable Config_spi_nor...
Hi,
I encountered a "Thread kick off too slow" issue. Let me explain it
My develop environment
Hardware: nRf7002-DK
SDK: 2.6.1
A. I copy the sample nrf/samples/net...
Hi, i'm trying to modify the thread coap_server sample by adding bluetooth configurationg following this webinar https://www.youtube.com/watch?v=hY_tDext6zA&t=2199s
I'm...
Hello,
I'm working with the nRF Connect SDK version 1.8, using Zephyr and a CC1101 radio module. The radio communicates via SPI, but at the beginning of the process, I need...
Hi
which function do I need to call in a peripheral to stop advertising?
Where Do I find the documentation for it?
which function do I need to disconnect ?
Where Do...
My company has been assigned a 16bit Service UUID from Bluetooth SIG, which we wish to use in advertising with the Service Data AD type.
However as soon as I swap our binary...
Hello, I was wondering if somebody has an explanation (or has seen the same problem) for the following event:
We have had 5 units with NRF9160-B0 in the field for testing...
Hello, On my nRF9160 custom device, I have enabled XPOFWARN to automatically switch off the modem in case the voltage gets too low. It's working fine. This case happens when...
Hello Engineer Greetings Of the Day We performed DFU over BLE with secondary slot in External flash that operates using SPI . I needed some clarification on the outcomes ...
We have a custom board with nrf5340 and we use SDK v2.5.3 for software development. Our BLE signal strength seems too weak with the default TX Power setting. So we would like...
