Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
IDE: SEGGER Embedded Studio for ARM 5.32 SDK: nRF5 SDK 15.0.0 and nRF5 SDK for Mesh 2.1.1 demo: examples\sdk_coexist\ble_app_uart_coexist\pca10040\s132\ses\client_pca10040_s132...
I am using NRF52 DK board and removed SB9 track to connect my ammeter for current measurement . I have taken ble_app_blinky ( peripheral example ) from SDK15.3.0 .
My application...
hi,all
I'm using nRF52833, s140.. pca10100.
I want to read my pcb's touch gpio..
If I touch it, it falls down to low. ( I checked it with scope..)
When viewed through...
I'm testing USB audio demo. I changed bit resolution of APP_USBD_AUDIO_FORMAT_DESCRIPTOR 16 to 24 but the widows10's USB audio device is still 16 bit. how can i do that?
Hi!
I'm trying to pass the BLE data to the PC using nrf52840 DK.
To do so, I've started with the ble_app_uart example and it was able to build fundamental features–find...
Hello,
our application requires to emulate keyboard, e.g. to write strings like "hello world\n" as it might be typed by the keyboard. According to the recommendations...
Hey I am using nRF 52840 DK
I am reading temperature from Segger code and displaying it in the log
But I want to display that value in my android nRF Mesh Application...
Aim:- To read temperature and humidity over a mesh network and display it in an android application
Devices to be connected in Mesh :-
nRfF52840 Development Kit x2 ...
I created a 500ms timer to send mouse movement as follows.
m_mouse_movement_send(5,0);
When the device runs there, the device will restart. The error code is NRF_ERROR_FORBIDDEN...
Hi engineers,
I want to use the pin P1.09(NRF_GPIO_PIN_MAP(1, 9)) as GPIO, but when I initiate it, it seems fail.
I've looked through the relevant issues here, but got...
Hi,
I am currently trying to build a project using a nRD9160 with legacy code and am receiving this error when trying to load an existing project:
I understand...
I am not able to successfully use your nRF UART app to communicate with your nRF52840 DK. I get a warning when installing the app that it may be too old for my version of...
I'm still learning BLE development so I apologize if this is a basic question.
Here is a screenshot of a recent capture I did with the nRF52-DK. The bluetooth sniffer is...
Pardon my ignorance of the nuances of Security and Encryption but what I am observing is a bit perplexing.
Every time I run the nrfutil command to generate the bootloader...
Hello, I use sleep_mode_enter() to put the device into sleep mode, however, the RTT print a fatal error after sd_power_system_off(), I don't know whether the device is in...
