We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi, we have a NPM1300 chip connected as I2C slave to a nrf5340, acting as I2C master. Everything works fine, but there is a small detail in the NPM user manual that I would...
Please help me!
I have installed nrfutil from the official website, and configured the environment variables, and put the.exe file in the corresponding location, but there...
Has anyone got an idea on how to avoid resetting the device, as soon as USB-C is connected to it? I want to avoid losing state when charging the Thingy:53. Also, has anyone...
Hi,
I have a question about the System Monitor section of the nPM1300 documentation:
https://docs.nordicsemi.com/bundle/ps_npm1300/page/chapters/core_components/saadc...
Hello,
I'm implementing a device based on the NRF52840 Dongle and the hids keyboard example. The basic functionality work, so that I can send pressed keys to a connected...
Hi,
I am trying to implement a ble module in a fall detection application. I added a ble_service based on the BLE fundamentals course lesson 3, which works just fine alone...
Description:
Hello,
I want to measure the distance between two BLE devices with high accuracy . I have already tried using nRF52840 modules , but the results are not very...
Hello,
I'm trying to detect a UART_ERROR_BREAK on an USB ACM CDC interface of the nRF5340 using NCS2.7.
The returned error code is always 0xffffffa8. How do I clear...
Hi
I have a simple application which is comprised of a notification from peripheral to central , and a write without reponse from Central to peripheral.
In windows every...
Greetings,
We are using a nrf54L15 and trying to use the GRTC Clock output functionality as described in 8.10.4 of the datasheet.
We need the most accurate clock output...
In the next step, I compiled the “Serial LTE Modem” firmware example from the examples folder and flashed it onto the nrf9160DK.
The “Serial LTE Modem” application works...
Hi,
I use the nRF9160dk and I want to use nRF9160's internal flash which has 1MB flash to store a few data. But I cannot find any guideline about using nRF9160's internal...
Good evening, I have recently purchased an nRF52 development kit which I would like to use for my project. Currenty, I would like to provision external devices using this...
Hello, I have a custom board that was designed for me, but based off of the Acconeer XM126. It is very similar with a few minor differences. The person who designed it has...
I'm developing based on the Nordic Academy example here, but I noticed that when transmitting a large amount of data, something is limiting the amount sent by the NRF52832...
