This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi, I am following this post to set the TX power level of the beacon. https://devzone.nordicsemi.com/f/nordic-q-a/45871/setting-tx-power-level-in-example-ble_app_beacon-for...
I can not register 2 services 128-bit vendor-specific UUI in one project at the same time. For example if I use services ble_lbs_c.c and ble_nus_c.c the sd_ble_uuid_vs_add...
Hi,
I've got some code (at https://github.com/espruino/Espruino/blob/master/targets/nrf5x/jshardware.c#L1201-L1318 ) where I use nrf_drv_uart to access the UART. I don't...
Currently my colleague and I are trying to connect his stm32 qfpn48 MCU to nrf52840 via SPI protocol.
I tried the sample in SDK and successfully setup a workable dummy SPI...
Is there a sniffer firmware for this board ?
I download "nrf_sniffer_2.0.0-beta-1_51296aa.zip" but it appear that no fw exist for this board.
Is it correct ?
Seba...
Hi, I could not find in documentation function or some command I can call in software to restart the MCU. Is there such a thing, and can this be done? Best regards, Voja
hi ....
i want to test the bidirectional working , i am using uart peripheral example , i have taken the rxd,txd,cts pin from Nrf52840 board interfaced with TTl uart .....
I am working on nRF52DK. This will act as peripheral device and smart phone device will act as central. From my observations i could see 48-bit mac address and GATT local...
Hi
I'm currently doing an internship about bluetooth mesh network.
I'm using the light switch example with a client board and a server board, provisioned with the nerf...
We have an interesting difficulty, whereby after a period of time which varies never longer than 12 hours, often around 6 hours, our application disconnects from the network...
Hi,
I have NCS v1.0.0 on an NRF9160-DK v.0.8.3 and I am trying to run a program written before the SDK update. I can build and flash the program but when I try running...
Hi. I have a multilink central based project running on nRF52840 SDK15.0. I have added code from another example to do advertising as we want the central to advertise some...
Hi ,
I am build and run the source code of nrf Uart app from nRF UART App git repo. When I clicked on the connect button it opened a new sub window ,I know it is the list...
Dear all,
we would like to use nRF9160 DK as a CAT-M1 reference device for our local test purposes. Usually we use iperf tool for UDP traffic generation. Do you have any...
Hi,
I try to use the nRF52840 as a sniffer. I tried to follow ( https://infocenter.nordicsemi.com/pdf/nRF_Sniffer_UG_v2.2.pdf ) but I block in the 2.2.5 part.
When I run...
