Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Dear all,
I have nRF51 DK and I use mbed CLI to build my application that is simple mbed-os-example-blinky.
Also I have SDK11.0.0 and I built the ble dfu bootloader (...
Hi there
I did an upgrade of the bootloader from SDK 12.2 to SDK 14.2. I am using the nrf52832 chip. It is basically the same as the secure BLE DFU example from the SDK...
Hi everybody,
I was looking for a better way to update a data, like a 32-bit-word, without the need to erase the entire page. Part of this question is already been asked...
I was going through all the supported SDKs for the nrf52840 and in all of them, it is mentioned that the ESB and FreeRTOS support is not there yet. Could someone please let...
Hello, I'm trying to implement a buttonless DFU via ANT for a custom nRF52 board. I've got the 212 v4.02 Softdevice and I'm using the 14.0.0 SDK. I am able to transmit and...
Dear
i want to nrf52832 to collect accelaration sensor data(SPI communication 8MHZ).
The sensor output datas per 250us,nrf52832 will lost the sensor interupt when 52832...
Good evening. I write a project on nrf51822 in which there are a number of services with a set of characteristics (write and read). I need to limit access to some characteristics...
Hello, I am working through the tutorials to understand how to better use the SDK. I am currently on the Advertising tutorial and have gotten a strange error that doesn't...
I'm developing an accurate and low drift millisecond-resolution timer on the NRF52. I'm limited to the resources on the NRF52 itself. Details of the system:
Initialise...
Is there anything special required to make a n52832 work the very first time the chip is programmed? Fuses to set, etc?
I'm new to nordic chips and I was handed a board...
While creating a DFU bootloader based on the bootloader_secure_ble example, I was having trouble getting a device to boot into DFU mode.
Initially the device would get...
(Sorry for the formatting. I don't know what's going on with it--the preview looks ok!)
I'm creating an application that uses
a modified version of the ble_nus
example...
Hello guys,
I have problem, I activate the BLE and connect it to my tablet application until then nothing wrong happens. But when I use sd_ble_gap_disconnect() to disconnect...
I plugged my nRF52 evaluation board to PC using a micro USB cable, dragged a ble_peripheral hex file from Nordic examples to the mounted JLINK drive, started up nRF Connect...