We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi I am using the tutorial from https://github.com/bjornspockeli/custom_ble_service_example . I have uncommented some of the starter code from ble_cus.c. My understanding...
I am inquiring about something I know very little about but will try to communicate for the information. Smart phone applications can be opened through a QR code which utilizes...
Hi,
We are using ncs tag v1.0.0.
I am using i2c_scanner example firmware. It works find when used as it is.
When I added "UART2" in this firmware i am getting hard fault...
Using the ble_app_uart example, Using oscilloscope to measure the time interval of broadcasting, two development boards are used respectively. One development board is nrf51422...
Hello, rols and hkn:
I got two different answer about watchdog and hardfault in devzone.
1. watchdog can't reset hardfault. https://devzone.nordicsemi.com/f/nordic-q-a...
https://github.com/bjornspockeli/custom_ble_service_example
I am currently following this example with SES on my NRF52840 DK (PCA10056). I copied the ble_app_template example...
Are there any recommended alternatives (& nordic plugins) to the discontinued Bluetooth Developer Studio? I'm looking for a tool to make the process of creating custom GATT...
Hi! I want to copy data from internal flash to a statically allocated buffer in RAM. I get a DACCVIOL hard fault try to do this by memcpy. The hard fault depends on the number...
I need to send 5 sensor values received over SPI to an app over BLE about 5 times a second. I also need to send a few configuration parameters from the app back to the nrf52...
I am using nRF 52 DK connected to Arietta with ARM Linux (4.2.6) 32 bit.
when I was trying to install "vcpkg" using "./bootstrap-vcpkg.sh", I am getting some errors as shown...
I have a phone app which talks to my peripheral device running the nrf52832 and so I will eventually add another peripheral device which ideally can communicate directly to...
Hello everyone!
I'm working on a project where there are 2 microcontrollers: the Nordic nrf52832 and a 3rd-party uC (can't disclose it). A protocol to transfer the firmware...
I feel confused about bearer. what's the difference between mesh-bases bearer and PB-ADV bearer or PB-GATT? there is little knowledge about mesh-bases bearer within mesh profile...
Good afternoon,
At the place I'm working there's 2 main projects using the nordic SDK, while one runs on the 12.3 version, the other is very outdated and still runs on...
Hi,
I'm having a problem at the moment with code based on Espruino on nrf52.
I connect as follows:
ble_gap_scan_params_t m_scan_param;
memset(&m_scan_param, 0,...
