But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi, all!
Is it really possible to timestamp 4 GPIO edges in parallel with the nRF52?
It would need to be as fast as possible and some edges might be simultaneous so...
hello:
I'm looking for a bluetooth solution for our equipment. We need a chip that simulates a serial port, what we send by SPI port, it is received in the mobile and the...
Hello,
I would like to understand how can I make use of the macro ERR_TO_STR_TWI in order to know what error is being given by my TWI module function.
I have tried something...
I am attempting to run the SoftwareSerial example on the Arduino Primo.
The example code does not work and I am wondering whether the pin assignments are correct.
Example...
If I use PWM "nrf_drv_pwm_simple_playback"
and that will go to "start_playback"
How can I catch end point after it finish entire function?
BTW, the process will keep...
Hello All,
I am working on nRF52-DK, nRF52832 PCA10040, and i want to know on how i can wake up my device from sleep mode using hardware interrupt. I am using interrupt...
Hello,
i want to power off and on the board using the Long Press Button Event.
Is this possible? Please help me out to resolve this issues...
Thank You
I used to get all my output by running cat on /dev/ttyACM0. Now I only see the first few lines, until the filesystem gets mounted.
How do I prevent Linux mounting the filesystem...
The Bluetooth Mesh Light Switch example provides an example of how to program a Bluetooth Mesh application where the client model is on the provisioner device and the server...
Hello
what we want :
One central and several periphals.
The periphals will have different DEVICENAME.
Is this possible with the NUS Service?
The doku says ;
Note
...
Hi all,
Anyone has tried if the Tx power of nrf 51822 is changed from +4dBm to -20dBm, how much power (%) can it save, in a ballpark figure?
Thank,
Carl
hi
i am using the sdk 12.3.0 when i'm trying to compile the file under blinky/pca1028/s130 i'm getting this error anyone can help me please
............\components\softdevice...
I am using S132 V5.1 in combination with nRF5 14.2, and I cannot find where I can set hvn_tx_queue_size.
We are using the new option to configure the softdevice using the...
any one can help me to fix this erreor please
............\components\ble\ble_services\ble_nus\ble_nus.c(41): error: #59: function call is not allowed in a constant ...
Hi,
I am trying to send an command line through UART to the UART device such as MP3 audio module.
MP3 module is taking only hex values. How to send it to the UART device...
