Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
I'm using PCA10028, SDK12.3 and android(7.1.1) application using BleProfile.
My application implement ADC using app_timer and indicate adc value each timeout.
The narrower...
Hi,
I have bought a Smart Remote 3 and now I wonder if there is any user manual available for it. I want to test the features it has out of the box before I start to modify...
Using SD130 v2.0.1 on nRF51822, I would like to be able to change the advertisment interval after first connection.
My app is based on the HRS sample, with a modified avertising_init...
Hi,
I am trying to bond Thingy to Android device. But, it is rejected by the device.
How do I bond Thingy to Android device? Any Hints would be helpful.
Thanks
Has the dev kit gone through FCC? i.e. can the SoC/antenna design be replicated on a custom board so there are high chances of passing certification tests?
Hello ,I hope the speed of NUS can be achieved 7K Byte/s. The data form phone to uart is ok,but the data form uart to phone is not.I tested the Bluetooth part separately.Loop...
How to make an encryption on nRF51822?
Does it need to set
sd_ble_gap_sec_params_reply(m_conn_handle, BLE_GAP_SEC_STATUS_SUCCESS, &m_sec_params, &sec_keyset)
the...
I want to flash a client and three servers with the BLE mesh simple light switch example:
infocenter.nordicsemi.com/index.jsp
The third instruction on the above web...
Hello,
I've recently properly started programming my nrf52832 DK with segger embeded studio playing a little with the debuging tool break points modifing example ect.....
I test ble bond with 'ble_app_gls' in sdk 12.3.0
eg.nRF5_SDK_12.3.0_d7731ad\examples\ble_peripheral\ble_app_gls\pca10028\s130\arm5_no_packs
my phone is meizu mx4, android...
I feel Slave Latency is unnecessary.
For example :
Connect Interval is 100ms,
Supervisor Timeout is 4000ms.
So the Slave Latency must be 39.
if I set Slave Latency...
Hello,
When using extended ATT_MTU without DLE, and the MTU is larger than the LL data length, I know that the MTU is divided into smaller LL packets when sending.
But...
Dear Nordic Devzone,
I want to run an Arduino Ethernet Shield with the Wiznet5100 on the nRF52840. I was wondering if there was an easier way to do this then having to...
I am designing the BLE solution using nrf52832 . The board will be two layer board with solid ground plane in the bottom layer and signal and ground pour in the top layer...
