Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi,
I'm wondering if the slave connection interval range is the same as the GAP peripheral preferred connection parameters i.e. does it make sense to do the following ...
Hello!
I'm developing thread application with COAP communication. I've got problem with message queue on router. Everything works fine when operating as a child. I have cyclic...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi,
I'm trying to get started with the nRF51-DK with the ble_app_template. I want to get it working in the Rowley CrossWorks IDE. (From what I understand this is the same...
I am having trouble running softdevice_enable. Here is what happens:
After main(void) starts the code is:
log_init(); // WORKS
clock_init(); // WORKS
buttons_leds_init...
Hello,
I'm using a nRF51822 to send data to the iPhone using the NUS service. I'm using the oldest SDK4.x and v5.x S110 soft device. I know that the least connection interval...
Good day.
I`m very new to nordic chips.
I`m try to use NRF52832 as TWI master with OLED display based on SSD1306 with I2C.
And got this.
Yellow is SCL, Blue...
Hi,
I am trying to use the FDS for saving some variables and displaying them again later. I have downloaded the NRF52-fds-master sample code posted on github. However,...
i am working with mpu xx example given in nordic website. it seems code is working fine i.e. compiling and dumping into nrf52 DK, But not showing any output values.
i was...
I am using an Nrf51822 for a project. I looked in the datasheet and it said that there is a built in WDT for the chip. It also says that clocks can't be used while in systems...
I want to use in my project tft 1.8 display with st7735 controller. I'd like to use some based code but can find nothing except on infocenter nordic
As I understand there...
Hi,
I am writing a boot loader which does not need to use the soft device as the image is being transferred over an SPI interface.
I have merged the softdevice and my...
Hi
I suppose that Multiple connection to centrals is available from BT4.1.
Is it possible to realize bu S110?
If it is so, which version is available the specification...
Hello, I made some boards on nrf52832 and I was testing the PCB.
The test program is ..\nRF5_SDK_12.0.0_12f24da\examples\ble_peripheral\ble_app_hrs.
(I have downloaded...
Hello! Just got a few NRF51822's.. looking to just brodcast a few basic URL's.. if someone can point me in the right direction or maybe let me know where I can hire someone...
