Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi,
How to implement two sets of SPI on the NCS v3.0.0 nRF54L15 P2 port? If it can be achieved, please provide the corresponding IO ports for these two sets of SPI.
Kind...
I have been forced to upgrade to the nRF54L15 from the nRF52840 DK. The example code in the SDK for the nRF52840 the 'ble-peripheral' had example code for 'ble_app_uart' which...
Hello Nordic,
I’m using ncs\v3.1.0\nrf\samples\peripheral\radio_test` to test the nRF54L15 with PHY set to `NRF_RADIO_MODE_BLE_LR125KBIT`. However, the RF spectrum measurement...
Hello,
I am developing a custom board based on the nRF54L15.
Every time I do RTT connection from the extension i have been asked to prompt the target device (nRF54L15M33...
i working bare-metal, using HW registers directly.... no zephyr, no SDC....
i'm able to successfully receive packets through the RADIO RX path, but now want to add a timeout...
Hi,
After installing nrf sdk v2.9.3 trying to build application under Windows fails with the following message:
Trying to run any command inside the NCS shell/terminal...
With nrfconnect SDK V3.3.0 seeing commissioning issues with light bulb sample with nrf52840dk and google home. The logs are given below. Please help with resolution
Thanks...
Hi,
We have an application where we have a working DFU over BLE with SDK 2.9.1 but once we have migrated to 3.2.4 it has stopped working. Something has obviously changed...
Good morning,
we are using the Zigbee stack (ZBOSS) on nRF52 devices with Green Power Sink enabled and we are integrating a Green Power door sensor.
nRF5_SDK_for_Thread_and_Zigbee_v4...
Hi, I am working with the nRF54L15 on sdk-nrf 3.2.3 and I am experiencing an unexpected behaviour with the NFC T4T stack regarding WTX frame timing.
Here is the observed...
Hi Nordic team,
I’m working on an nRF5340 project using MCUboot with the secondary slot placed on external flash.
I found a strange issue related to pm_static.yml . My...
Hello Team,
I am trying to test a PDM microphone (MP34DT01‑M MEMS) on the nRF9151 DK using nRF Connect SDK .
So far:
I have successfully tested I2C and I2S DAC audio...
The drag and drop programming was working fine on previous boards.
We just purchased 10 boards thinking that they were the same, but the don't seem to work.
PCA10040 3...
