Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hello,
I'm using the nrf52840 and SDKv16 to interface with an SD card. An SD card block is 512 bytes. I would like to do this:
1. Get the card ready for a write (use blocking...
Hello,
Not a 100%, but in this Nordic video the nRF52840 might be using the Alexa Gadgets Toolkit. Alexa Notepad demo 2020 https://www.youtube.com/watch?v=CdLfg-6kQs0
...
Received our 52840 DK, loaded, via nRF Go Studio, s140_nrf52_7.0.1_softdevice.hex. Loaded, via IAR Workbench, ble_app_blinky_pca10056a_s140. I clicked to go button and whamo...
Hello. Nordic team.
Once again I had questions, this time related to serialization .
While the preparation of the driver is on the PC side, I am studying the examples...
I have an issue with reseting the board using a hard reset via an external button. The onboard development kit reset works, but I am trying to perform the same task using...
Hello,
I was reading the nrf_libuarte_async library, and noticed that in the
app_timer_handler -
calls the
local_app_timer_start -
again and starts the timer again...
Hi,
I use a 3rd party board from raytac ( https://www.raytac.com/product/ins.php?index_id=95 ) on my PCB and I have problems with a bluetooth low energy connection. On your...
Hello,
I'm trying to get sleep mode working on a nRF52840-DK with Zephyr or Mbed OS while using UART.
It is possible to achieve low current consumption in sleep mode...
I opened an example from the SDK 16 in:
nRF5_SDK_16.0.0_98a08e2/examples/iot/lwm2m/lwm2m_client/pca10056/s140/ses/iot_lwm2m_client_pca10056_s140.emProject
When I try to...
Hello!
I want to develop my own app, and the source code refer to proximity in nrf toolbox. Now, i have some questions:
1. What function in the source code of serverManager...
Hello
In my application, I would like to allow smartphone that are Bluetooth V5 compatible to receive more information in advertinsing packets from my devices (via the ...
Hi,
I want to optimize the transmission efficiency and thinking of sending larger packets than 2048 bytes of MQTT would help.
We have limited battery power, and looking...
Hi,
I am started working on nRF9160 Power Management. I want to power down all devices(sleep mode) expect motion sensor, Wake if motion is detected. I went through System...
Hi Team,
Can you please point me where I can change the compiler optimization level in SES v4.52 and I am using nRF9160 module.
Regards,
Praveen Palaparthi
Hi Team,
We are using the NRF52840 Device with S140 Soft device for our BLE applications. As part of this we have enabled the flash storage as well.
We are unable to write...
