After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I am using nRF9160: LTE Sensor Gateway to connect wiht nRF52832. My problem is I cannot re establish connection between the nRF9160 and the nRF52832. I have tried to create...
I am using nrf connect app on ios , the device is getitng on device mode but it is not showing DFU button on it , but it is working when using android app of it
And...
I want to generate a custom delay of one microsecond without using any timers By simply Executing instructions I want to generate. is there any possibility please let me know...
I have a rather strange issue.
I developed an application on the nrf52832 which amongst other, communicates with an ST Micro accelerometer LIS2DE12. The application works...
Hello,
Library seems to have limitation to 1kB. I'am talking about deffered mode.
You can increase NRF_LOG_DEFERRED_BUFSIZE >1kB, but it will crash if you try to print...
Hello, I am new to developing with nrf and have been trying to follow tutorials on individually setting pins as output. I am working on just getting a specified pin to blink...
Hi everyone,
Recently, I downloaded the SEGGER Embedded Studio, release 4.18, and start the development of a Heart Rate Monitor using nRF51422 and SDK 10 (softdevice s310...
I am only able to successfully trigger the ACK payload interrupt on the nRF24L01+ if I mismatch the payload lengths on the two devices; 4 for the nRF24L01+ and 1 for the nRF52840...
Hi everybody,
Intro facts :
I'm migrating from SDK 13.2.0 through SDK 14.2 to SDK 15.3.0. My program build on SDK14.2 but my product didn't work as expected, then I...
I need the P9 connector pinout (or complete schematic of Thingy:52 ) for programming my Nordic Thingy:52 using SWD. I have found this topics:
https://devzone.nordicsemi...
Hello, according to your website, nRF24 Series family is not recommended for new designs... as substitution you recommend to use nRF52 Series family. Can I ask you for the...
Aim: interface nrf32852 with i.MX6UL based Linux board through UART and configure hci of bluez. Board: nrf52_pca10040 SOM : nRf32852 OS: Zephyr UART: we followed HCI_UART...
Dear Nordic Team,
We are developing a custom board with nRF9160 with application of tracting device.
I am new user to this module and designing our device with target...
Hello,
I'm searching every where but i can't find what i want. Actually, i'm using two device and i really need to synchronise the execution of a process on both of them...
Hi All,
I have a problem to enable notification on my Android phone, i followed the tutorial on android web page (section bluetooth low energy) but my app crash, i have...
