After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hi, I'm using this post to upgrade from SDK 11.0 to SDK 15.3.
All goes well, until I uploaded an application: then I get a hardfault somewhere at fds_init().
I found...
When I start nRF Connect v3.2.0 the first window starts as normal, but when I click on Open Bluetooth Low Energy the nRF Connect v3.2.0 - Bluetooth Low Energy window is blank...
How can application code interrogate the SD140 to identify which version (such as 6.0.0) is running.
We pre-flash (before SMT) our nRF52840 with a bootloader and SD140,...
Hi ,
What does the handle parameter in status_handle(access_model_handle_t handle, const access_message_rx_t * p_rx_msg, void * p_args)function (generic_onoff_client.c)...
Hi all,
I am trying to reduce the connection time between each connection to the minimal posible
Connect -->Transfer data -- Disconnect
I am facing two options...
Hi,
I want to make simple software that runs on PCA10056 using SEGGER and SDK. To learn how to use SEGGER, I copied exsamples / template_project and tried to imitate blinky...
Hello guys, i'm using nRF52832-DK with S132_v3.1.0 and SDK v12.2.0.
When other BLE device write some value to my characteristic, how do i know
that my characteristic...
Hello,
I am using a custom board that has a DSP and the Lairds BLE module BL651 that has nRF52810. I have written a simple program that sends a test data byte to the DSP...
I use nrf51422 dk, device: s310 2.0.1
Then i want to download "bootloader" from example floder by keil 4
but it can't work
and show up "JLinkARM.dll not found. please reinstall...
Hello,
I want to install nRF5x Command Line Tools on macOS, I found this user guide, infocenter.nordicsemi.com/.../nRF5x_Command_Line_Tools_v1.3.pdf and on page 5, it lists...
hello guys,
I using nrf52840 development kit and segger embedded studio. I want to write a program to implement spi protocol, can I get a simple reference code to write...
PWM output with stable frequency
SDK: 15.3.0 Example: low_power_pwm Device: EYSHJNZWZ (nRF52832)
I want to output PWM with a stable frequency. In the above sample, PWM...
Hi,
In order to speed up network registration times I'm trying to do a band lock to 13,4 (Verizon & ATT within USA), so I'm issuing the below AT command which responds with...
Hi,
The baseline PSM sleep current of our device with all of the additional support circuitry is 100uA, and have just integrated FOTA capability.
However when we set CONFIG_BOOTLOADER_MCUBOOT...
