Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hi,
I am using nRF5 11.0.0 SDK softdevice 2.0.0.
I have implemented a RTOS application with beacon adv.
I also want to add UART service to the RTOS application.
...
Hi,
I am trying to use the Power Profiler Kit (PPK) to asses the power consumption on a nRF52840 - PDK. I have not managed to get anything wokring.
The exact hardware...
I am using 3 nRF 52840 dongles and want to establish mesh network between them. So I flashed the dongle with the softdevice (s140_nrf52_6.0.0_softdevice), bootloader (mesh_bootloader_serial_gccarmemb_nrf52840_xxAA...
I have flashed the the mesh serial hex file to nRF52840 dongle through nRF connect programmer application. I am getting following error
1. Reopen device failed
2. Nordic...
Hello All, In one of our product we are using nrf52840 Bluetooth + MCU IC. Size of Product is very tiny. which types of Antenna is better for range of 25 meter to 30 meter...
Hello good morning,
I am using nrf52840 device. I am sending 20 bytes using notification at different notification intervals like 30ms, 80ms and 1sec. But at application...
Hi, I wrote the firmware in SDK 11 preview, and when migrating it to SDK 11 the NFC code does not work, also it seems when the NFC startup code is executed none of the GPIO...
Hi All,
I've not enough experience in nrf51822. I'm developing a battery powered device using the Nordic nrf51822 pca10028. I want to connect two nrf51822 pca10028 boards...
I would like to use the latest ARM Compiler Version 6 ( armclang ) because I need some features of the C++11 language.
Is it possible to use the latest ARM Compiler Version...
Hi all,
I am using keil uVision 5 and nRFgo studio version 1.21.
I am trying to flash softdevice and application in nRF52832, but my device(nrf52-DK) is not getting connected...
I'm having some trouble getting interrupt from RTC1. I'm initialising as follows.
I have an interrupt function as follows.
I'm using the gcc_startup-script. We're...
I have Zephyr stack for BLE hci_uart without any error it got compiled in nordic controller part, but i like to use zephyr stack in host without linux OS. Is it possible to...
Hi,
If I do a directed advertising (peripheral device) with specific peer address, then will the peripheral device visible to other phones ( whose peer address does not...
I have tried out the Running Speed and Cadence Application of SDK 15.1 with the new DK "PCA 10056" (1.0.0, 2018.19, 683681562). We used the Samsung S8 and S9 with Android...
