This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi all,
I wanted to know the default values for the different NRF Radio paramateres in the ble_uart example.
I want to make some tests but not sure what is set as default...
Hello sir,
we have completely develop product using nRF52832 and S132, sdk13.1, and its great working fine with BLE. But for same application we want to use wifi module...
For my audio application, I need to convert pcm out from pdm module(nrf52832) to an audio format (mp3,wav) continuously. Is there any method or procedure for this??...or any...
This may be intentional, or an oversight but the
uint32_t app_gpiote_user_register(app_gpiote_user_id_t
* p_user_id, uint32_t const * p_pins_low_to_high_mask, uint32_t...
Dear All,
I am starter for nRF52832 DK. Could you please tell me where the start point is and where I can find demo programs ?
Thank you so much.
Best regards,
...
I want connect with password with my nrf52832 via Android phone. How I can do it? I do not want to do pairing how in example project "ble_app_gls". I used Android 6, SDK14...
we have used the ble mesh sdk v0.9.2 to implement long range ble mesh network on nrf52840 SOC
it is successfully working with s132 softdevice. with default configuration...
Hello,
I'm trying to switch from softdevice s332 v2 to s332 v5 (tried also v4), but I get this error: "region RAM overflowed with stack".
I'm guessing the problem is in...
Hello! I am testing project "ble_nfc_pairing_reference". When my NFC device touch the NFC antenna on the device screen is written: pairing; connecting; could not connect....
Hello,
I have an nRF52 DK, running S132, as a client. After scanning and connecting, I use ble_db_discovery_start, which finds the devices of interest, connects, and finds...
As the title specifies, on writing to the registers mentioned, I receive a Fatal error.
Here's the test code
void save_ram()
{
__DSB();
NRF_POWER->RAM[0].POWERSET...
Hi,
I would like to know if anyone ever tried to alter the SEGGER J-Link OB Code that goes on the ATSAM3U2CA-AU IC (this is the IC that controls de PCA10040).
I'm asking...
Dear support,
I am working on some custom boards embedding the nRF52832-CIAA chip using SDK-v11.0 and s132-v2.0.1.
I have got 9 custom units and out of them only 4 work...
