Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I am porting my code (previously on 51822/SDK V12) to 52/SDK V14.
I have RTT logging working well on 51/SDK v12. In SDK V14 I noticed that the log module now is in experimental_log...
nRF52832
SDK14.0
Hi, how can I protect the bootloader from being overwritten? Ideally, I would never be updating the bootloader so it will be a permanent part of the device...
Hi
How stable is the RTT module and how trustworthy is it?
It is marked as unstable and I do not get any messages from the modules.
I use:
#define NRF_LOG_BACKEND_RTT_ENABLED...
Hi,
i would like to implement a very low power counter and used the template from this post . I've modified the example and used TIMER2 in counter mode triggered by LPCOMP...
Hi,
I'm trying to create a local network between an nrf51-DK and a mobile phone, android or iOS. The main goal is to be able to get TCP/IP connection between the nrf5x...
I am writing firmware for a BLE Nano device using the Nordic SDK 8.1. I was having problems where my device would suddenly stop printing to UART and stop trying to bond with...
I'm trying to set up a ble mesh with 3 servers and 1 client on an nrf52 PCA10040 dev kit. Upon debugging, I'm getting an error that says: '64, APP_ERROR: C:\Users\sesa463145...
I am using a NRF52-based platform and have BLE code based on the ble_app_hrs_c Hear rate monitor system.
Having set up for scan, I see many device (we have a lot of beacons...
After migrating from sdk 13 with buttonless dfu based app I meet follow error:
my app get FATAL error after exactly 3min. I guess it something related with power down mode...
I have a 3 channel setup on my SAADC module, which I sample according to a LFCLK timer. I notice after the first called to nrf_drv_saadc_sample() and receipt of the ADC results...
hi,everyone!
we use the example
"nRF5_SDK_14.0.0_3bcc1f7\examples\ble_peripheral\ble_app_uart\pca10040\s132"ble_app_uart,
we also defined
"#define NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
At the very end of this post from Nordic Info center I am doing the exact example at the very end.
infocenter.nordicsemi.com/index.jsp
This is the start to do a transmit...
Hello
I'm trying to track lost packets in a connection by showing the sequence number of each packet received. Specifically it's about an application that sends new measurements...
Hello sir,
I have develop product on nRF52832 DK and now i using custom nrf52832 board Here . I want to continuously on my device with BLE advertising continuously no sleep...
