Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi,
I am developing ble apps with the BL600.
I am coding a source file with the keil IDE. And this source is deployed to the nRF51 DK board through the nRFgo Studio....
hello,
i am unable to update application or softdevice or bootloader via master control panel 3.9.0
while doing so, it shows error:"FAILED TO OPEN TRANPORT BACKEND". ...
I followed the Nordic Tutorial located here . I'm using a PCA100028 Dev Board, MCP 3.9.0.6, and a Segger J-Link Plus. I'm using Keil uVision5, and used the pack installer...
I have a set of characteristics on my ble peripheral (nrf51) which I display with nordic control panel tool (android). but when I deleted one characteristic on the peripheral...
Hi, I am evaluating the use of Gazell and BLE as a possible solution for my project. I had heard that there was a way to have both BLE and Gazell running on a device at the...
we will do some measurments and answer when we get some time to spare for this. Others are welcome to answer/comment freely about their experiences/knowledge.
I have some custom hardware (nRF51822) with a couple sensors on it and would like to have the data sent via BLE to a smartphone. This may be timer based on triggered by an...
Hi :
I want to update the firmware of 24le1 over the air ,follow the 3 step ,fail.
download "rf_adapter_nRF24LU1P.hex " to the nRF24LU1 by nrf6310,and connect to PC...
I am using the nrf52832 to communicate uart with hw flow control and a baudrate of 9600 and fifo.
Everything is going well most of the time, but sometimes the other device...
I write an infrared receive driver on example ble_app_uart with softDevice 6, but it not work after I use softDevice 8.How to fix it ? Is there an offical infrared receive...
I'm trying to generate a 1kHz PWL and call a function every 1ms the code is below.
My initial though was to set TASKS_CLEAR once the timer reached the max pwl value.
Oddly...
Hello,
I am using multilink central example to connect to multiple peripherals. But I am facing a problem in connecting 2nd device.
After connecting the 1 st device, upon...
Hi,
the S130 supports multiple connections for the Central role. Is it possible to connect to multiple devices at the same time? E.g. calling sd_ble_gap_connect() asynchronously...
Hi,
My aim:To change the UUID,Major,Minor value beacon
What I Have done:I created one custom service with 3 characteristics.Each characteristics for each parameter.I am...
