This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Is it possible to have 1micro second interrupt using timer 1?
I am unable to achieve it.
If I try for 4micro second, I observe toggling of pin at 8 micro seconds?
...
Some examples require SDK 7.1, while the newer tutorials use SDK 8.0. I'm not sure how to switch between the SDK versions in Keil. I see the below lines in my include paths...
Hi.
Currently, the following results came out in the power-saving support .
■Our App
・Advertising Status
1.04mA ~ 1.13mA
・Connection Status ★1
1.044 ~...
Hi.
After stopping the Advertising,I measured the current.
For some reason, usually it is consumes about 1.1mA.
Because too large current consumption,
As a result...
Hi I using nRF51822, and want to know about the Nordic driver support LMP feature
Do you have any document about driver support? Or any software development document except...
Hello, I need to create a high resolution/high frequency PWM signal on the nRF51822. I have been using the new PWM library in the 8.1 SDK and can't quite get there.
From...
Hello. After a couple of s210 and s310 projects, I am attempting an s120 project. I built a client SDK but sd_nvic_EnableIRQ returns error code 0x2009 or NRF_ERROR_SOC_PPI_INVALID_GROUP...
I'm running the "Beacon Application for Eval Board" example for the S110 soft device on an nRF51822.
( devzone.nordicsemi.com/.../a00070.html)
I'm using another BLE...
Hi,
I was wondering if it is regual that configuring softdevice for a low frequency oscillator 32.768 kHz using the function:
SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
Hi,
Here is output of my chip and i want to read it but there is a problem 25 uS low width (T) is to quick for nRF51822
Can you give me some tips, how to read this 3 signal...
Hello all,
I notice that this library isn't listed in the "SDK Common Libraries" for S210 - is it ok to use this? Internally it does seem to be ANT-aware, even though softdevice_handler_init...
Hi everyone,
I'm using NRF51822 controller for an application, to store 2 float variables in the memory using persistent storage manager feature.
However, when I try...
Hi All,
I try to implement the DFU funtion in my module, but the message return is “Not Supported”.
Please suggest me, how could I do about it?
Thanks.
Vic
...
Hello,
Is there a restriction that I cannot have same address LSByte for radio pipes?
It seems that i am failing to receive data on pipe 0 if for example I have pipe 0...
