Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi All.
I am trying to download the Bootloader to nRF51822 Dev Kit using nRFgo Studio (32 bit, v 1.15.1.2691) but getting an Error.
"ERROR: Attempted to write to UICR...
Hi, I am trying to write code to run the nRF8001 chip from a PIC microcontroller. I've been messing around with nRFgo Studio for generating the setup data, and I've noticed...
We need to send some custom data in advertising packet.
Is it possible to use 'ble_advdata_service_data_t' with UUID of a standard service (e.g. battery service or device...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
Hey all:
I have the Dev and Eval Kits and a handful of dongles. In addition to one of the Chinese nRF51822 devices. I have successfully connected via Segger debugger, used...
Hi.
I have a custom nRF51822 PCB with SWDCLK and SWDIO Header. I have a nRF51822 Dev Kit.
Is there any way to use the J-Link from Dev Kit to Program the Chip of the...
Hi,
I check the state of an channel (sd_ant_channel_status_get()) and get 0x13. Which mean the channel is assigned. But sd_ant_channel_unassign() return with ...CHANNEL_IN_WRONG_STATE...
Your served radio transmitter/receiver example using PCA 10000 USB dongle with PCA 10001 evaluation kit. There is only one-byte send/receiving example.
So, I was to send...
Hi,
I programmed nrf51822 development board as central device, with the s120_nrf51822_1.0.0-3.alpha_softdevice and ble_app_hrs_c profile on top of it, i am using nrf51_sdk_v5_2_0_39364...
Hi,
I am trying to generate a constant 250ms pulse on a certain pin:
NRF_TIMER0->MODE = TIMER_MODE_MODE_Timer;
NRF_TIMER0->BITMODE = TIMER_BITMODE_BITMODE_16Bit;
...
I explain my hardware, An MCU + NRF51822, Communication is done via the UART TX RX between them, baud rate is 9600.
MCU through UART transmit data to NRF51822, then NRF51822...
My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi sir
In the Developed zone, I found how to read RSSI value as below. According to nRF51822 RM, RSSISAMPLE would be 0~ 127.
Actual RSSI is – (RSSISAMPLE) dBm. But, I found...
Hi
We are using the UART demo to communicate with the nrfUART app.There's a condition some
time when it connect,it will disconnect immediately,anybody know what's the issues...
