Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
This question relates to the unofficial gcc Makefiles available here:
github.com/.../nrf51-pure-gcc-setup
Using these to build a project based on the sample proximity...
Hi,
I just tried to toggle a led when a particular button in the evaluation board (nrf51822) is pressed, i just referred the gpiote sample code and started modifying it...
Hello,
I'm working on the nrf51822 with s110 stack and 5.1 SDK.
Wy functions are not described in the documentation but just enums and data types ?
I'm looking for informations...
I'm wrote a simple test to persist data using pstorage.
But I'm unable to load the stored data.
I'm using gcc and debugging with gdb. So I can see that storage_cb_handler...
Hi,
I am working on a project where there are moving devices. Devices can only move if a wired button is pressed. In fact, for security reasons, there are two buttons connected...
I've been looking at this for the better part of a day and can't seem to pinpoint what I'm doing wrong here. Does anybody want to take a quick peek at this project and tell...
Hi,
I would like to use the PCA10000 dongle hardware and antenna design for my PCB, i got some questions:
1)I have just UART pin outs extra, I would like to reduce the cost...
This question relates to the unofficial gcc Makefiles available here:
github.com/.../nrf51-pure-gcc-setup
These are great and I've managed to get as far as compiling...
To all successful developers.
I want to write some predefined parameters into the stack. So the problem is the adress.
Example: The nRF51 is part of a medical device....
hi,
is it possible that we can use s120 stack as a central, at this stage to work with our customized profiles?
or it will support only SIG profiles
regards & thanks...
Hello,
I've completed the ble iBeacon like application we are working on, with some custom GATT services/characteristics as well.
When I use LightBlue on a MacBookPro...
There is a check box on nRFgo Studio, Lock entire chip from readback. But a lot of chip can not burn one by one
Can I use AES block encryption to do this?
Hi
We are investigating Hong Kong certification for our nRF9E5 based equipment in the 868 band
The snag seems to be that required channel centre frequencies are "odd...
Hi,
My setup is a nRFgo QFAA FA with S110 v.6.0.0 and Motherboard. I am using the latest SDK 5.1.0. The Master Control Panel drives the nrf51822 USB development dongle...
Hi,I have a Nrf8001 module, use a arduino to control it.
Now,I can use this module to connect IPHONE APP(BLE Probe and LightBlue),sending and reciving data are all ok,the...
