Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
Hi,
I have a device that throughout the uart data to ble,recently I find a problem that in the case of weak signals,the data sequence is out of order.
Here is the question...
Hi,
I am trying to run the sensor example as provided in the Mesh SDK. I am getting the log as mentioned:
13691970>, main.c, 475, mocked motion sensed = 0% <t: 13691973...
Hi there,
I'm using the softdevice sd_ecb_block_encrypt to encrypt my 16byte block data as follows:
When my data buffer is filled, it called aes_encrypt(),
void aes_encrypt...
Hi Nordic,
I are working on battery operated device.
Need to measure battery percentage using ADC.
Let me know how can we select range of 0-100% for battery voltage...
Hello,
How do you flash custom firmware into the Nordic Thingy 52? The Thingy doesn’t reflect changes that I make to the firmware files and instead just turns off the...
I'm trying to find an example of how to properly buffer sensor readings between connections, and then transmitting the buffer on connection.
Is this just done via the user...
Hi,
I have developed a piece of software that only uses the GPIOs on the APP core to evaluate a sensor. The software worked on the development board processor so I made...
Hi support team,
In my case, i want to auto disconnect to ble central after some minutes with no message transfered, so i create an timmer and set event compare and clear...
We are developing a beacon with nrf52810. We test ble_app_beacon example and a modified example( the difference is, advertising packets are connectable to be applicable in...
I've configured UART2 on the nRF9160 to connect to a nRF52840. The nRF52840 generates a payload and sends it over to the nRF91. The payload size during testing was 65 bytes...
Hello,
I am developing using nrf2840 PDK, SDK v17.0.0, S140
I have made two services, one is to control the led blinking rate via nrf connect android app and the other...
Hi,
Is it possible to have dual transport for DFU (UART and OTA)?
I read this in the forum: https://devzone.nordicsemi.com/f/nordic-q-a/28118/multiple-dfu-transports ...
I have nRF52840 as the central and nRF52832 as the devices. I have the device names as TELCO_456, TELCO_457, TELCO_458 in the connectable advertisement packet. I have disabled...
I am trying to capture sniffer logs for a custom BLE peripheral using nRF51 dongle and Wireshark. I am following this guide here to install the Sniffer tool in Wireshark....
