Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hello i cannot get uart to work correctly on these pins. The board seems to reset when i try to run uart on these pins. I can get them to work on pins P0.06 and P0.08. I think...
I could not find update info on this;
When I use mergehex to combine SD, app and bootloader, MCU just boots into DFU mode.
When I program SD, bootloader and app, MCU...
I have a nrf52832 running as a BTLE peripheral running up a couple of services including one custom with a characteristic i wish to be modified by the peer.
Data is being...
Now I'm using NRF52832 to communicate with other MCU(STM32) by UART.
STM32 will transmits about 40 bytes data to NRF52832 per 10ms.
Here is my configure referenced Nordic...
Are there any dependencies between the connection parameters configuration and pairing?
I am using nRF52840 and SDK 14.0.2 and ATT_MTU example. I am trying to add pairing...
I am trying to implement bonding with the Uart example in SDK 14. I have followed the instructions for how to use implement device manager and then migrating to peer manager...
Hello there, I need to specify the LDO that will power the nRF51824.
What would be the max current consumption for nRF51824 at 3.3V?
I saw a similar calculation for 51822...
Hello, this might be a stupid question but if I have a Bluetooth 5 module that is advertising and another module getting the RSSI-value without actually being connected to...
Looking for some advice on how to handle connectivity issues in damp/wet weather.
We've found that our NRF51 device works well indoors, but when placed outdoors overnight...
as I've been looking everywhere on the infocenter for a migration document from sdk 14.0 to 14.1 I was thinking that not finding it meant no changes needed. Of course that...
I am using nrfutil to generate ECC private keys and public keys. However on an apple device the keys ANSI X9.63 it is represented in X,Y, K parameters. How do i match the...
Hi everyone,
I'm trying to compile a ble_app_uart exemple using my own Makefile (The exemple compiles and works fine), but i got an error from the linker.
error: objects_application...
Hi,
two quick questions (nRF52832):
What is the value of t_LPCOMP,STARTUP (I didn't find it in the PS).
Can PSEL be modified while LPCOMP is running?...
Where in the official documentation can I find what the boot order/proedure is for the nRF52832?
For instance: This post gives a coarse overview which is great but I am...
Hello,
I want to achieve bidirectional data communication between one central and two peripherals. My two peripherals will have different services. Any my central device...
