After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I am porting our sdk 8 based firmware for the sdk 11. Now the code crashes at the code below:
err_code = sd_ble_gap_device_name_set(&sec_mode,
(const uint8_t *)name,...
We followed the instructions for the beacon example for nrf 52 dk.
Multiple attempts to change and reset the board, there was no change in the ad packet.
Can someone...
I'm using the nRF52832 chip without an external crystal. I configured it to use the internal RC with:
nrf_clock_lf_cfg_t clock_lf_cfg;
clock_lf_cfg.source = NRF_CLOCK_LF_SRC_RC;...
Hi,
I have tested ble_app_hids_keyboard for using whitelist.I find that this example is bond+whitelist. If bonded, the peer address will be added into whitelist. But when...
Hi,
I test Whitelist function in the example ble_app_hids_keyboard_pca10040_s132 using SDK12.2.0.
I donnot understand the code in "case BLE_ADV_EVT_WHITELIST_REQUEST:" located...
Hi all,
I have some problems with GPIO Interrupts.
I'm using nrf52832, s132 and sdk 12.2
The error is totally random so I don't know why is generated. The case is...
Hi,
We are using the Secure DFU from SDK 12.2, with SD132 3.1.0, on a PCA10040.
As a DFU controller, we use a PCA10031 with a SD130 2.0.1 and a project derived from the...
Hello,
We are migrating from IAR 760 to IAR 8.10 compiler does not produce the same assembly for the SDK12 inline function nrf_delay_us.
The original C Function is :
...
Hi, i am working on RTLS project. In beacons i want to enable DFU service using SDK 13.0. But I could'nt find a gothrough process to do the same. Please give me some link...
I am using S132 4.0.2 and SDK 13, and I have theese questions:
I have an application where BLE node establishes multiple concurrent connections (several as central...
Hello,
I'm having systematically an HardFault interrupt ~10 seconds after calling sd_soft_device_enable(NULL, &fault_handler);
This occurs on my bootloader code, but...
Hallo Community,
I am doing the example ble_app_uart using Eclipse, a SDK 13.00 and a board 10040, When i compile the main file I´ve problems with scan params:
#if ...
#define UART_TX_BUF_SIZE 1024
#define UART_RX_BUF_SIZE 1024
Why to send and receive buffer length of the definition of 1024 bytes, increase the value, again if serial port...
