i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
I'm looking to use this dk for a small project.
Has anyone made or seen a box for the devkit easliy available (.STL) for 3d printing?
And for added coverage, can I just...
The documentation for EVTEN in the manual, showing the RTC Tasks and Events system (Figure 45) led me to believe that if EVTEN for an event is disabled the EVENT will never...
Phone Model: model MX4 from MeiZu china
APP applied: nRF Master
experiment 1:
Here in my hand, when a android phone try to connect to the device which contain the service...
I just now saw the press release for the Primo .
In theory the bootloader should just to be able to be loaded to an existing DevKit either via NRFstudio or the NRFprog...
www.youtube.com/watch
Hi,
I'm a beginner in Iot. I found this interesting video and observed that NRF51 SDK and NRF Beacon communicate with each other. I want to send...
I have12 input pins to my application. But the code fails when I try to add the fifth button.
Is there a limit to how many input signals I can add?
static void gpio_inputs_init...
Hi,
I am using SDK 11 and S130 for my ble application. S130 acquires 108k of flash memory. How can I reduce it to less than 100k or should i use S110 since it uses just...
I have OCD for compiler warnings... I must use -Wall (I'm a freak like that).
In nrf_drv_twi.c line 433 there is a function twi_clear_bus. This gives an -Wunused-parameter...
Hello,
I was working on a nRF51422 and made a project using the example ble_app_uart_c. It works fine on the DK, but now I want to make it work on a board that has one...
Hello,
Does anyone know if the information and methods given in the links below are still valid for nRF52?
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../ ...
Hey,
We're are newbies with Nordic and are trying to program BLE HRS example code to run straight on the nRF52832 (instead of the PCA10040 target).
In order to do so we...
Hi everybody! I am here again bothering you with probably silly questions. I have, on my smart beacon kit, an application that uses an ADC and then sends the converted value;...
`Hi Guys,
My project requirement is that first time i have to bond and connect my nRF8001 BLE with peer device, once connected i have to find peer device address, after finding...
Hi everyone,
I was not able to find a full example in the SDK or online on initializing ANT to work with burst mode. Also, I was wondering if it's possible to setup ANT...
Hello,
I have a design where nrf51422 works as companion chip together with an other uC as main controller (STM32F4).
I need to reset the NRF from the main controller...
