i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hello, I'm an developer using nrf51822.
I have the same problem with this.
devzone.nordicsemi.com/.../
But this problem has no more discussion...
Here is my problem...
First I load soft device through nRFgo.
Then I run debug with eclipse.
I then step through code in main.c ...
(I'm using QFAAG0 chip)
Stepping worked fine when I used...
Hi,
I use a system with BLE softcore running - and can generate highly precise pulses with the gpio pins using Timer1+2 with interrupt service routines. Jitter might be...
Hi,
I want to use nRF51822 to do some development in the eclipse.I follow the document(nAN-29 nRF51 Development with GCC and Eclipse Application Note v1.1) step by step,when...
Using PCA10001 Evaluation kit, SDK v6.1.0_b2ec2e6 and SD s110_nrf51822_7.0.0
IOS app nrf Toolbox HRM on iPhone. Everything is working fine, get the advertisement, connect...
Hi all,
Short version: I want to make 200 devices using nrf51822 (and S130 v0.5.0-1alpha), all advertising/scanning at the same time, and process RSSI readings for proximity...
I am trying to find out what is the difference between nRF51822-mKIT and nRF51822 EK . Visually both of the boards look identical and the only noticeable difference is an...
I just tried setting up on Windows8.1 but can't see the "nRFgo Studio".
I got as far as step 4 on page 9 of "nRF51822 Development Kit User Guide v1.4",
but it doesn't...
I have a RedBear Blend and I want to talk to it from iOS.
I'm currently using the default setup provided with the Blend and RedBear's library over the top of the Nordic...
Hi, after a deep study of Datasheet I was finally able to have two 24L01+ talk to each other with a PIC18 program.
Now I need to make a step further using ACK Payload since...
Hello,
I am trying to verify hid_keyboard_demo app running on nRF51822 with android running device.
I have tested it with my phone running android kitkat and windows...
hiii.....
am doing a project for implementing broadcasting while in active connection... i hv broadcastd datas successfully but the problem is when i disconnect the connection...
I am unable to see any uart print output when running the uart_example with NRF51822. I am able to see the program execute via the debugger, but have not seen any output....
Hi,
I am trying to port ble_app_alert_notification example to PCA10000 board. I've modified the example code in order not to use buttons and leds (always clear bond informations...