Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Is there a way to prevent nrfjprog from disabling target power from the J-Link when programming? I've tried setting power on perm but to no avail, nrfjprog powers down my...
I would like to know the RAM usage of my nRF51822 application. I found this post discussing some of it, but there is no obvious conclusion yet. I am using Keil for development...
I am using nRF51822-QFAA_Rev2. S110 7.1.0, SDK6.1.0.
First, program bootloader, then program \s6310\s110\ble_app_hrs\arm\ble_app_hrs_dfu code.
I use Android nRFtoolbox...
When performing a DFU using the latest iOS nRF Toolbox I keep getting an "Error on init Packet Message:Operation Failed". The DFU works fine with the same firmware application...
HI:
i use master control panel to write data to 51822(sdk8.0 ble_app_uart),but i can't write successfully.i do as help information.and i have selected the right UUID and...
I've just got up and running with the nRF51 DK. I've had a play with some of the examples, and now I've started on my own project using ble_app_template_s110_pca10028 as a...
After startup, I was able to send a spi msg from the master (app chip) to the slave(nordic). But when I try to sent the second message, I did not get any response from the...
I am using the SPI Slave peripheral and attempting to send the nrf51822 bytes from another MCU.
Am I right to assume that there is, basically, a 256 byte max per transaction...
Hi,
I have nRF51822 board which works great with my app when running on iOS 7
The application listens for iBeacon transmission and displays them.
When i installed my...
Hi, I made a custom PCB.
I use a Revision 2 MCU.
The antenna is printed. I didn't used the chip antenna.
Sorry for not showing both the full schematic and the...
Dear all,
I'm trying to connect the NRF51-DK (PCA10028) with a LSM330DLC accelerometer over TWI (I2C). I'm using the ble_app_uart example, included the twi_master.h file...
I need to implement a function to store some parameters such as uart baud rate and use these parameter for device initialization, The parameter could be modified when the...
Hello,
I`ve got a working S120 peripheral BLE device with custom services and characteristics.
I am able to connect and bond with iOS and Android. But I cannot connect...
Hello:
Im rewritting a program from ST32F105RC to NRF51822.
In a part of the program of ST32, it checks if the interruption from pins 5-9 (EXTI9_5_IRQn) is enabled, and...
Hi,
I worked with temp sensor example and sofdevice s110 and something stuck on some function.
Anyway, I made readout from registers but softdevice blocks register access...
