I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
Hello Nordic Team,
We need to start RF performance tests using CMW500. we have access to UART pins of nRF52840 in our DUT which can be used to connect UART-USB adapter to...
Hello Nordic, I am using
nRF5_SDK_17.0.0_9d13099,
IDE Segger V4.52c
soft device s132
Can I transfer 8208 bytes on I2C with nrf52832 with EasyDMA, ignoring the MAXCNT...
Hi,
I try to understand the power consumption of the UDP example for NRF9160 with PSM.
I'm using the default configuration: RAT="00000000", RPTAU="00100001", no eDRX,...
Hi all,
I am trying to interface a BLE mikrobus module onto a Yocto based Linux SBC. I need to use Zephyr's hci_uart example to flash it onto the module, the mikrobus...
Hi Dev Team,
I am running a program that takes in sensor data at 10 min intervals and publishes it to my server through MQTT at 1hr intervals.
I have different threads...
Hi, I am using Zephyr BLE stack to check the HCI testing og the nrf52840_pca10056 module. I am useing Windows Subsystem for Linux for Ubuntu toolchain. While using the make...
Hi,
I am planning to buy a nrf9160-DK to build a BLE LTE-M gateway. I would like to ask if the gateway is able to communicate with a private MQTT broker/server instead of...
my project is freertos+nrf52832 based the templete in SDK; A sensor pin is connect to P0.17, and I configure it low to high level trigger interrupt.In the handler I will call...
Hi all,
I am using two nrf52840 boards and a Light-Switch example included in the mesh SDK. I want to observe packages sent by the client and packages arriving at the server...
SDK: NCS 1.4.0
board: nRF9160-DK
sample: lwm2m_client
Question:
I am testing SERCOMM module and nRF9160-DK, but there is difference in registration procedure .
When...
Hello, I migrated codes that I believed to be relevant to the UART output to a new project, namely the uart_init function and others, and it worked in main.c, which is where...
I am trying to use the connectivity firmware with an NRF52840 dongle to communicate with an nRF52840-dk through the nordic UART service, but I am unable to use the pc_ble_py...
Hello,
I am curently working on project with a nrf9160. I will use the nrf9160 as modem controled by a nrf52840 and command AT. I will send data true GSM every 12 hours...
