Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I have Nordic nRF52832 mini beacon device. How can i change UUID, Major,Minor values from Android and iOS app. Is it possible to change the those values from app ? If yes...
Hello, I want to measure the impedence of PCB antenna designed for nRF52832 based board.
I have the following quires.
Is it required to isolate antenna from NRF52832...
Hi,
I'm developing a server model and a client model(Both example are modified in accordance with the example of light_switch). In the example of client, I use the API...
hello friends,
i need to control 4 LED brightness using PWM according to accelerometer values. how can i do that
i am using SDK11, nrf52832, KEIL MDK5
i going to...
Hello,
Am using Freertos with SDK 13.1 and SD 4.0.5 on custom board.
My question is about buttons,We have one button need to configured for BLE Button.
I have board_custom...
Does the PPK require a Dev Kit (nRF5x kits) or a Segger J-Link, or is there a way to use it to measure current without either component? The user guide only shows setups with...
I have nRF52840 preview DK and want to read advertisement packet using nRF connect android app. I have read that Samsung galaxy S8 has Bluetooth 5 support. Has anyone here...
I am working on nRF52840 Preview DK. I want to generate a square wave with accuracy of ON and OFF time = 1 microsecond using timer for driving stepper motor DRB8825.
I...
Sir,
Please send eagle footprint if antenna used in nrf2401 module or send its schematic and board file of eagle... please help me
it is Meandered Inverted-F Antenna ...
Hi
I have a few questions I couldn't find about radio part of nRF528xx series.
Does all 3 chips have same radio module inside with same characteristics?
Can ANT...
I have a requirement where a handheld device containing a nrf52832 needs to be automatically paired to a switch (another nrf52832 device) when powered on, how can this be...
Hi triying to drive a Relay with Output but have tried every functon in "nrf_gpio.h"
this works with a LED perfectly :
nrf_gpio_pin_toggle(23);
in the main i configure...
I am currently working in the " ble_thread_dyn_mtd_coap_cli" multi protocol example.
Whenever I call printf my program crashes.
I think it has to do with the ble_nus service...
Dear friends,
I am trying to run the PWM in my project. I have:
added the PWM driver successfully (4.0.0-2.alpha, nrf_drv_pwm.c, nrf_drv_pwm.h) ;
set...
