I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
Hello,
I used translation software.
I am transferring test data from nRF52832.
I want to down the average current consumption in data transfer.
I am currently...
Hello,
here i explain the set up.
Cental_A Board :- scanning two peripheral
Peripheral_A Board :- advertise with name Peri_A .
Peripheral_B Board :- advertise with...
Hello,
I would like to know how I can check whether the SAADC is enabled or nor on my application. I am disabling the SAADC with nrf_drv_saadc_uninit(); after configuring...
I'm using the latest SDK (14.1) and have got a working COAP server running over BLE on a nRF52DK, and can exercise the service from my Ubuntu desktop without any problem....
Hai team,
Iam using the ble_app_beacon example program.
I found power profiling calculation on this link devzone.nordicsemi.com/.../ .
i calculated power consumption...
Hello,
I installed the new nrfjprog but it fails to write my nrf52 dongle:
ERROR: nrfjprog failed for an unknown reason. Run the same command again with ERROR: argument...
Hello,i want to get the mac address by sd_ble_gap_address_get().There is a error message as fellow: Undefined symbol sd_ble_gap_address_get(referred from main.o). Where is...
HI!
The use of simulation software I2C and the sensor module communication in my program, without the use of the protocol stack, the normal running of the program, but after...
Hello,
I am using sdk 12.2.2 and pca10040. I want to include the mac address in adv packet name. I am not aware of the api used to get mac address. I used sd_ble_gap_address_get...
HW: BMD-350
SDK: nRF5_SDK_12.0.0_12f24da
Sample Code: examples\dfu\bootloader_secure\pca10040_debug
I have my own firmware app.
Problem:
If I use Keil to flash...
Do I have to temperature dissipation? I attached temperature sensor on my board with nrf51822. I removed copper layer of around the temperature sensor. But it seems the temperature...
Hi,
I am using nrf51822(qfaa), sdk12.3, softdevice s130.
I am using the ble_app_uart (both central and peripheral) as reference for my development.
I have both central...
Hi,
I get following error when i try to compile nRF5_IoT_SDK_v0.9.x for target nrf52822
compiling x509_csr.c...
assembling arm_startup_nrf51.s...
(13): error: A1517E...
