Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
Hello there,
my goal is to wake up via NFC from POWER_OFF Mode (sd_power_system_off). Then right after the nfc wake up sending some information (e.g. UUID) via the NFC...
As a I2C master, I need to be able to read some data from a slave device the length of which I do not know beforehand. First byte I receive from slave is a packet type and...
Hi,
I want to estimate the battery life of my nRF52 device operating on a battery of capacity 800mAh. Device will advertise once in every 10sec with an advertising interval...
I print every 500ms. Here are the last few
timers:INFO:millis 510500, cnt 16728087
timers:INFO:millis 511000, cnt 16744474
timers:INFO:millis 511501, cnt 16760868
timers...
Hello,
I have measured the current consumption of the timer example of SDK13.0.0 with PCA10056.
With timer prescaler set at 16MHz i have 1.28 mA
With timer prescaler...
Hi, I got nRF52 DK PCA10040 device(s132) and follow the steps from devzone.nordicsemi.com/.../ to use arm-none-eabi-gcc(version 5.4) to build examples like blinky. I can successfully...
Hello,
I was wondering whether or not it's possible to achieve a data rate of 160Kbps using BLE4.2. According to what I have read on this nordic blog it should be feasable...
Hello!
I hope this question has not been asked before - at least I can't find it.
I do have an application with two vender specific services (128bit UUID's) and I want...
Hi,
i am doing ble_app_beacon code on nrf 52832 with sdk 11 and s132. the packet, its advertising should only be received by the device whose bluetooth address we are providing...
main.c ble_uart.hex
Hello,
I use nRF5_SDK_11.0.0_89a8197 and s130_nrf51_2.0.0_softdevice configuration to test the ble_uart program.
i use nrfgo Studio to load the...
Hi Nordic team,
I try to use SDK for Thread v0.10.0 cli example and run diag command, but it is disable as below
Could you tell me how to enable diagnostics module...
Hi,
I'm using nRF52840. I would use data length extension and set the MTU size to 247 when it works as peripheral. However,there would be some problem when it connect to...
