Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
Hi
I have working module which communicates via uart with another module. It works good, unless it is heated to 40C. After that temperature UART communication is not correct...
Hi Engineers!
We made our own ten (10) PCB's with nRF52840 MCU onboard fully according to "Circuit configuration no. 3":
1. LDO only mode (VDDH connected to VDD connected...
I have a custom circuit with nrf52832 which I am trying to program.
All i/o pins seem to be working fine except pins P0.06 - P0.10.
I'm testing it with mbed (digitalout...
Hi,
Thanks for taking the time looking into issue.
We are using Keil uVision 5.14.
Our target is a custom board (BMD200 eval Module based on nRF51822)
We were able to...
Hei guys,
for a new custom board based on nrf52832 where i have to minimize power:
have an external Li-Po battery, with a cutoff @3.0v, so the range will be 4.2v...
blesc_pairing_dhkey_check_failed.zip
Hello,
I used the example ble_app_multirole_lesc and paired with nRF Connect app. However I got the error message (in Bluetooth...
Hi!
So I have my GATT value of a service that I would like to update.
Sadly that value always stays at the initial value.
Below you can find my update function.
uint32_t...
I am using SDK12.0.0. ble_app_uart example, and I have change the clock to using LFCLK RC. I know from nRF51822-PAN_v3.1.pdf that we need to calibrate the LFCLK RC after reset...
I've managed to overcome all the quirks in setting up Eclipse/gcc development with the nRF52 PDK (PCA10056), and I can build the sample projects just fine. Here's my issue...
I arrived at step 8 in this tutorial
github.com/.../custom_ble_service_example
Now I'm supposed to propagate events to the application, for example connection state...
I am using a usual uart to bluetooth application and it works great, but I would like to set this application to be a known apple midi device, it seems I only have to add...
When running ble_peripheral\ble_app_uart example..... Of course I am a little bit
corrected.....
Beacons occasionally stop.
Despite the following settings:
#define...
Hi!
Is there any example app where I can find how to use L2CAP protocol on nRF52 series? Apple introduced L2CAP in iOS 11 and I want to give it a try but I can't see any...
