Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
I am trying to connect my thingy91 and preform an MCUBoot. This is not working and i get the following error code: Errorcode: CouldNotCallFunction (0x9) Lowlevel error: INVALID_OPERATION...
Excuse me, I use BSP_EVENT_KEY_0 to get into the sleep mode, however, it will go to the NRF_BREAKPOINT_COND and then reset the device;.
case BSP_EVENT_KEY_0:
SEGGER_RTT_printf...
I have developed data loggers based on nrf52840,it uses nus service,max payload is of 240 bytes,the device stores 30kb data in a spi memory.we have a custom built android...
Dear community, as already mentioned here https://devzone.nordicsemi.com/f/nordic-q-a/30622/nrf_cal_set_time-setting-issue-for-2100-year/121167 Im wondering how do you deal...
Hello. I need to calculate the RSSI value from the module nRF9160. I am using the nRF9160 DK 0.8.2. From the AT reference guide, there are two commands: AT+CESQ and AT+CSQ...
The new Bluetooth specification 5.2 will support transmission of audio data in a so called isosynchronous burst mode to external, BLE capable speakers, opening up a long asked...
Hi,
We are having some issues with the values obtained via ADC readings. We have a few designs using the nRF52840 where the analog reads from sensors are not stable. To...
Hi,
We used nRF52840 Dongle to receive BLE peripheral device 240Bytes notification. The connectivity that "Bluttooth low energy" (nRF connect) programmed can received 240Bytes...
Hi,
I am using NRF52810 controller, The power consumption of my board in SLEEP MODE is 200uA . According to datasheet the ideal current in sleep mode is 3 uA.
In advertising...
Hi,
I use SDK16 ble sec-bootloader and merged application image together followed by the guide of the website
unfortunalately , after flahsing fw_all_s140.hex to device...
Hello,
Question regarding GPS power consumption numbers in the nRF9160 data sheet (V2.0)
Section 5.2.1.16 GPS Current Consumption:
Are the current consumption numbers...
Hi,
I would used a RTC calendar (Years, month, day, hour, minute, second).
The smartphone connect to the nrf51822 and updates the date and time.
The nRF51822 must perform...
Hi,
Is it safe to call nrfx_spim_init() multiple times with and without a handler without calling uninit() in between?
I have an SPI device that needs a sequence of steps...
I keep seeing NOT_AVAILABLE_BECAUSE_PROTECTION errors on all sub-programs of nRF Connect when attempting to program the associated firmware (RSSI viewer, Bluetooth Low Energy...
Hi,
I am trying to create a Mesh network using CCT controlled lights and switch.
I am using nRF52-DK, I want to use one of the button for two functionalities i.e storing...
