hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hello,
we are currently using NRF_LOG_INFO over UART. We print out some values from time to time (seldom). Assume we never go manually to some of the sleep modes.
We use...
With SDK for Mesh v5.0.0 the STRATEGY_ON_POWER_DOWN doesn't work correctly over multiple power downs.
If an entry is set and the stack is powered down, the entry is written...
Hello!!
I am using Radio Transmitter/Receiver example from nRF5_SDK_17.0.2. I am able transmit and receive data on NRF52832. Is it possible to receive the data apart from...
Hi,
I have a huge issue with NRF52832 and DFU on custom board. I have a custom characteristic in my application to switch to DFU after proper PIN typing. Then I call this...
Hi All,
I'm trying send custom board(nrf52832) sensor data to DK by ble uart and multilink.
When I build the code in Keil. I got the message:
..\..\..\main.c(544): error...
I am using the light bulb example and connecting to the Zigbee2MQTT. The Z2M is running on a docker with logs level set to debug.
So from the light bulb example, how can...
Hi. So, pretty sure I've got the firmware installed right and plugging the dongle in creates a "/dev/tty.usbmodem1101" entry. Problem is I have a crash in Python:
This...
I am going to send a sequence of notifications and the documentation provides this information
The API functions that may consume an application packet depending on the...
Hello,
I am using the nRF52811 for my project. I am in the layout design phase...almost completed and I need some clarifications before I launch the first Proto.
I don...
I have found a lot of people having problems debugging with the SD enabled, but we are not using any BLE atm. We are just using the softdevice for OTA updates. But this is...
hi support team,
i just want to confirm, for mesh SDK, i can only find "APP_UNACK_MSG_REPEAT_COUNT" to increase message repeat count, for ACK message, i can't find any...
Hello NRF Team,
We are using nrf51822 chip for one of our product. Currently, we are using a GPIO connected to user button to Turn On the device from system off sleep mode...
Hi,
I have an issue with broadcasting Eddystone TLM + iBeacon, my project is based ble_app_eddystone example and nRF5_SDK_17.0.0_9d13099, SOC is nRF52832.
Beacon advertise...
Hello,
I am developing a circuit which is based on nRF52820. I got the boards manufactured but they are not functioning properly for some reason.
Following are the errors...
