Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
chip: nrf52840 aQFN package
5~10% of the products were defective. by causing analysis, There are short some pins bottom of chip.
I already read this guide after this...
Dear All,
I am using the NRF51822. I downloaded All the latest SDK and Segger Embedded Studio. No matter which sample project I choose I get the same error.
C:/Nordic_Semi...
hello,
please guide me to active LTE in Iran. i used several modem firmware release and can't connect to the network. im using nRF9160 DK and testing with AT sample programmed...
The Nordic Uart Service example in SDK14.2 with SoftDevice 5.1.0 appears to use Write Request judging by the timing which limits transmission to about 30mSecs per packet with...
Hi,
We're using the Android BLE library from Nordic. It really helped us handle a lot of the things we didn't want to think about handling on the bluetooth stack. (Thank...
Probably frowned upon but like being able to work from raw datasheet, so I know that I can. So given that the datasheet would suggest that changing a GPIO pin to be an output...
Hi,
On latest SDK (15.3)n nrf52832, PCA10040, on ble uart bare example, I get a bug when stopping advetising:
line 659: "p_advertising->evt_handler(p_advertising->adv_evt...
Posting this in hardware because it seems like the most appropriate...
We are conducting some localization experiments where we will be capturing advertising packets of...
It has been working with no problems. Neither the At application or the asset-tracker one will work. Is there anyway I can test/ find out whether there is an issue with the...
Hi,
I want to ask you, if they're any phase locked loop (PLL) that can be used ?
My problem : I have two square signal generate by an Arduino Nano and a PWM on the nordic...
I have inherited some code that is production after doing some extensive testing on battery life have noticed that after writing to the flash my power consumption on the Nordic...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I have few queries on RTC.
1) There are...
Hello, I'm fairly new to embedded software. I'm trying to flash the ble_app_uart program from the command line (windows 10 / nRF5_sdk_15.3.0_59ac345 / nRF52840 / Eclipse IDE...
Dears,
I have bought nRF24L01 transceiver module and I am trying to interface with Desktop directly but connected MAX232 between. But I am not able to communicate with my...
