Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hello!
I use 2 board nrf52840! I want to transfer large data ( 1~2MBytes) from board1 to board2 with wire to connect. Can have solution for me? (SPI I2C or uart).
According to the description of S132_SDS_v5.0 on page 82, when the establishment of connection, in accordance with the BLE protocol, softdevice will be interrupted frequent...
I am using nRF52840 and the power profiler. I am trying to measure the current to evaluate the scheduling of BLE. Now I am using the ble_uart_c example and I changed the scan_interval...
I'm trying to set up SPI example from SDK12.3, but I get error at line 53 of main.c
static const nrf_drv_spi_t spi = NRF_DRV_SPI_INSTANCE(SPI_INSTANCE);
It's saying...
Dear friends,
i am using Power Profiler Kit with a nRF52832 DK(PCA10036). However, i just find three versions of SDK on www.nordicsemi.com/.../nRF52-DK . My problem is that...
Hi nordic,
nRF5_SDK_14.0.0_3bcc1f7\Raga\examples\ble_peripheral\ble_app_ancs_c FDS\pca10040\s132\arm5_no_packs
I had a problem when I was using FDS，When I use the GC...
Dear friends,
I want to use Power Profiler Kit to monitor the current waves of nRF5x DK, and i followed the following configurations:
The PPK board (PCA63511) is connected...
How do you do
Now use E: \ Nordic \ nRF5_SDK_12 2.0 \ examples \ peripheral \ pwm_driver \ pca10040 demo5 pwm_driver routine
There are two problems:
How to change...
I run into this topic during seeking an answer to my problem and for me, as well as for the author of that question the answer doesn't work properly. But wouldn't it be easier...
I was able to create a Distribution package with the command as shown in the following photo.
I have taken the zip file from email app in my iPhone and have opened in...
Programming the bootloader
How the MBR knows the start address of the bootloader?
pape says : This start address is defined in UICR.BOOTLOADERADDR, which is located at...
How do you do
1.Now want to set the PWM output frequency is 60 hz, but with an oscilloscope test is 60.24 hz, here more than 0.24 hz.How can I do the precision of the precision...
