When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hello,
I discovered that Keil's software pack for nordicsemi devices are way outdated. Is there any chance to update those? I am quite redundant to add all sdk manually since...
I've been trying to increase NRF_BLE_GATT_MAX_MTU_SIZE on SDK13.0.0 + SD123 5.0.0 trying to follow examples such as
this as well as Throughput and Range Demo
For e.g...
Hi, to use the bluetooth 5 long range feature, do both the transmitter and receiver need to be configured to in this mode to work? Do you have any example AES 128 that I can...
SDK： nRF5_SDK_11.0.0
Softdevice： s132_nrf52_2.0.0_softdevice
project：examples\ble_peripheral\ble_app_hids_mouse\pca10040\s132\arm4
I have some questions about bonding...
Hallo,
I try to port some existing BLE application from SDK 12.2 to SDK 14 that used the S132 Softdevice.
With 12.2 it was possible to configure bandwidth requirments...
Would it be possible to use BLE for a sensor network with aprox. 40 battery peripherals measuring a float at 100hz? 50hz? For one central unit, or how many if needed.. The...
Hi,
One of my pca10040 stays on bootloader mode.
I have tryed copying J-Link OB-SAM3U128-V2-NordicSemi 160212.bin file on the bootloader drive but it stays the same. ...
Hi Everyone,
I just purchased an nRF52840 PDK and I am trying to program it via nRFgo. I erased the flash, selected the latest s140_nrf52840_5.0.0-3.alpha_softdevice.hex...
Hello,
My team and I are experiencing a problem with our custom DFU Bootloader, which is based on the Experimental Bootloader Secure Serial example (SDK 13), running in...
Hi,
My SDK version is 13.0 and my problem is when I run the examples\ble_peripheral\experimental_ble_app_buttonless_dfu project the 52DK seems ok but when I use the DFU in...
Hello:
I am setting up my nRF52840 development board to work with the S140 softdevice on Segger Embedded Studio; however, I am running into issues with the flash_placement...
Hello,
I've seen some conversations around the forum for applications that must share the same ID. My application must share SPIMO and TWIMO (ID 3, base addresss 0x40003000...
Hello,
I want to make beacon with my uuids. I am referring to code ble_app_beacon code from sdk 12.2.2
I have made changes according to my requirements in my code.
I am...
