Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
hi,
i am using eclipse IDE to build the blinky example with soft device s130(using SDK11). i added the make file and .ld script and linked all files which is required....
Dear Nordic family,
I tried programming Raytac MDBT40 with the LED blinking code (taken from the example project of SDK 8) which worked with nRF51822 Bluetooth Low Energy...
Hi
I have been using the DFU for quite a while. I adapted the boot loader to my hardware and compiled it using Keil.
All my other code is written in another environment...
Dear Nordic Developers!
When I call the sd_power_system_off() function to put the MCU to system OFF, after that I can still see the advertiser device in MasterControlPanel...
Hi!
First of all, I'm using the nrf52 PCA 10040 DK, with SDK11.0.0, and my Soft Device is 132 2.0.2.
I'm developing an app for comunicating with a sensor via SPI (send...
Hi,
Am starting custom service to support custom profile and it works without any issues.
But when I add DFU service also to start after custom service DFU service fails...
Hi All,
I have a question about use of super/ultra-capacitor in a circuit using a module BLE (nrf51822 inside) instead of accu Li-Pol / Li-ion ?
it is possible to use...
I am looking to use the nRF51822 in my product and have been given a nRF51822 development kit however i have been looking for access to the Firmware and Hardware files and...
I have an nRF52 DK and have compiled (with gcc) and flashed an example that contains the line
NRF_LOG_PRINTF("SPI example\r\n");
I get the appropriate LED flashing...
Hi,
I'm trying to discovery the content of a vendor specific GATT service.
So far I'm receiving the BLE_DB_DISCOVERY_COMPLETE event and I'm able to see that I got 4 entries...
Hello,
I have a BLE Nano (nRF51822) and I want to develop an app which will find all BLE devices around (MAC addresses and RSSI) and send it by UART/SPI . I've used nRF...
Hi.
I'm using nRF51822AC, S130.
I made source code for RF test as below.
NRF_RADIO->SHORTS = 0;
NRF_RADIO->EVENTS_DISABLED = 0;
NRF_RADIO->TEST = 0;
NRF_RADIO->TASKS_DISABLE...
I tried MQTT subscriber example code, it compiles and loads successfully but it doesn't show the LED lights accordingly as I press the buttons, meaning that MQTT state is...
