When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi,
When nRF9160 is used as a co-processor and an external host MCU is used to interface with nRF9160, what are the serial interfaces that are allowed? The at_client example...
Is it a better choice to use the NCS for nRF52840 development, given that it is the new platform going forward? Am I painting myself into a corner developing with nRF5 SDK...
Hi,
I'm trying to develop buttonless DFU and followed below guidelines and got to work all the way to step6. Thank you.
https://github.com/gamnes/nRF52832-buttonless...
I want to build my own board configuration:
The default configuration of the board is as follows: ncs?v1.2.0,zephyr?boards?arm?nrf9160_pca10090
How do I generate my own...
Hello
I'm using NRF connect the app to perform read and write on nrf52840 board SDK ver of 15.0.0.
I can perform the write and read operations using nrf connect app, and...
Hi
I'm working on a custom PCB based on nRF52840 soc and SDK version 16.0
currently I'm trying to interface my MCU with an external flash of model MT25QL01GBBB
my...
Hi,
I would like to interface ICM20948 with nrf52832 and communicate over TWI or SPI. That thing I don't understand is the logic voltage of the bus. In nrf52 specifications...
Hello,
I went through the instructions in the Getting Started Assistant to setup nRF Connect SDK for Linux but I am getting the following error when trying to build a project...
Hi,
I am programming nRF52840 dev kit (SDK16) as a peripheral with S140. Smartphone is central.
data needs to be transferred between both.
I need the dev kit to consume...
Hello, I’m using nRF52840 with SDK 16 and SD 7. My purpose is to save as much power is possible using high-frequency clock (32MHz) only during periodic duties and BLE activity...
What are best practices for updating an nRF52832 via UART from an nRF52840? There seem to be at least two problems to solve:
Transmitting the 832 image via BLE to the...
Hello,
I'm measuring the idle current using a PCA10040 DK, SDK v16.
Finding that the idle current is about 3uA (which I think is correct) after any debug operation like...
Our setup is using a NRF52832 with SDK15.0.0.
While working with a time sensitive external circuit where we both sample the state of the GPIO and enable LDETECT on it...
I have just received my nRF52 development board and I have tried to program one of the pre-bjui;t examples (Blinky). The USB drive on the board appears and if I drag the hex...
Hi,
I'm using an application with FreeRTOS , nRF52833, SDK 16.
When I'm trying to get it into low power (sleep mode) the system still consumes ~4mA
In vPortSuppressTicksAndSleep...
