Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hello,
While building a custom board, I need 52832 to communicate with a modem at regular intervals, send AT commands and read modem responses. nrf_serial library in IRQ...
In the documentation for “Bootloader and DFU …” / SDK16.0.0 is written “you can use such a bootloader, for example, to switch between several applications”, but I can’t find...
I connect one central and two peripherals
Both peripherals set the connection interval to 100
Observing PA / LNA shows that one is communicating in 100ms
But the other...
Hello.
I have question about output OOB and public key.
I create my Android app for Thingy Bluetooth mesh purposes. I would like to start output OOB process (then Thingy...
Hi,
I am using the nrf_log_backend_flash in SDK15.3 with IAR 8.32 on Window10. From what I see in the release notes, no improvements were made for 16.0.
In my application...
Hi,
Good day!
Statement of porblem: We are developing appliction using nrf52832. In our application we have Capacitive touch button and capacitive wheel sensor for user...
Hi,
I am using bootloader and application based on SDK15.3.0 and SD s140_nrf52_6.1.1_softdevice.hex.
I am also using our own BLE transport layer in application to receive...
Hello, I can see in the datasheet of the NRF52840-CKAA-R that the recommanded inductor value for DCCH is 10uH +-10% (configuration no. 4). Unfortunately, we experience some...
Or may be another procedure to make a list of surrounding beacons nearby using nrf52832. We are beginners, sorry.
What do you recommend to start with?
Sdk16, 7.0.1 Softdevice...
Hi,
I have configured pin 10 (STATUS_BUTTON) on my own design board using a nRF52832 chop as follows:
I am intending to use the internal pull-up resistor to pull the...
Hi,
I'm trying to emulate a server device with pc-ble-driver-py, I recently moved from version 0.11.4 using Python 2.7.12 to version 0.14.0 using Python 3.7.4. I'm trying...
Hi,
I am using segger studio and NRF52810 for my development. I started with the NRF52 dev kit and complied with the sample app given in PCA10040e folder.
Now I want to...
Hi All,
I'm trying to figure out the best way to implement the security between two industrial IoT devices. We don't have a good out-of-band channel for more "traditional...
Hi,
I'm using Thingy:91 and I have built and flash the asset tracker software. I have connected the external GPS antenna (MIKE3A or similar), see picture.
How do I check...
I am using nrf52832 chip along with softdevice as a peripheral. There is a requirement wherein we want to encode the advertisement data.
Came across ble_advdata_encode(...
