Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi.
I am trying to start development using Thingy:52. To start, I tried the firmware from the download page ( https://www.nordicsemi.com/Software-and-tools/Prototyping-platforms...
The Limitations subsection of the Zigbee Section here contains the following paragraph:
- OTA DFU: Migration from the nRF5 SDK for Thread and Zigbee version earlier than...
After installing nRFgo Studio v1.17.1 on Windows 7 64 Bit (using the administrator account), I get an error message in the Log section just when I start the program:
"JLinkARM...
I'm using SDK 14 and trying to build the ble_app_buttonless_dfu example. I'm using Linux environment, so gcc for building. When I try to build the example I'm getting an error...
Hi, I was just wondering why there is a "nrf_delay_ms(200);" in the SPI Master example in SDK 16.0.
Here is the code in the main function where it is located :
while ...
Hi Support,
Now I am developing over Nordic 52840 DK (PCA10056). My environment as below,
(1) upon SDK (nRF5_SDK_15.3.0_59ac345)
(2) softdevice s140_nrf52_6.1.1_softdevice...
Hello,
I am using the nRF SDK for Mesh v.3.1.0. To achieve periodic publishing, I set p_pubstate -> publish_period . step_num = 1 instead of zero in the configure step in...
Hi,
I plan to design my own hardware based around nRF9160. Prior to this, I want to verify that I can use the nRF9160DK as a debugger for my own board. As an initial test...
Hello,
We would like to develop a wireless sensor network using the 802.15.4 stack in nRF SDK.
I wanted to know if it is possible to port the existing 802.15.4 example...
Hi,
I'm evaluating the Raytac MDBT50Q devkit, using nRF52840-DK to program it. I'm testing the system with SDK project nRF5_SDK_15.3.0_59ac345\examples\ble_central\ble_app_uart_c...
Hi. I am currently evaluating nrf9160 on a Thingy 91 board and have the environment for the asset_tracker application up and running.
I want to be able to handle JSON messages...
Hi,
I would like to have a system such as follows:
Taking sensor data storing it locally till around 100 samples (Once per second)
Log this data to the SD with a time...
Hello,
I was wondering if there are production ready fully pre-certified modules for the nRF91 Cellular chips? Like what Rigado (u-blox has it now) made with the BMD series...
Hi,
I would like to use the nRF52840 dongle to connect to 8 devices using Ant+ and to around 8-24 devices using Bluetooth.
Is there a maximum number of devices of Ant...
Hello to everyone,
I've just started playing with NRF52 DK (NRF52832 SoC). It is my first time with ARM MCU. I've had prior experience with atmega328p and MSP430. Although...
