I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
We need to sample two digital inputs GPIOs at rate of 100khz-1mhz. How can we do that?
The QDEC is only good for up to 128us (~7khz) which is too slow for us.
Is there a...
I'm not able to get clear/un-corrupted data across the ttyACM on the nrf52840-PDK. I must be missing something, seems like this would have been solved a million times, but...
I recently experienced an issue with a race condition between peer manager and FDS in SDK 14.2 which was resolved under this case:
https://devzone.nordicsemi.com/f/nordic...
Hello,
I develop entirely on Linux and I am unable to find the --sd-req / --sd-id required for generating a dfu package zip using nrfutil . I am using developing for the...
I defined custom service (NRF51822,S110) to send sensor data. Code follows. Here I enabled notifications for new data. I can able to receive data, if I enabled notification...
Hi,
I have the following set up:
The remote: nrf51822 acts as central
The wheels: Each wheel has nrf51822 acting as peripheral.
The remote needs to first connect...
My application needs to be notified of large current draws due to the activity of the nRF8001. The active signal works fine for this purpose, but why is it available only...
What is the typical expected receiver sensitivity when performing BER test (1Msps, 16 byte packets) of the radio module ? The spec refers to 2 values: -93 and -96 dBm (p.231...
Hello,
We are considering merging the Eddystone and iBeacon features together, packet types toggling at each interval tick, then we assumed that we should take the Eddystone...
My device is sending a beacon under DEBUG, but not under RUN.
The issue started when I converted the scan_and_forward example to use a 16-bit device address.
It steps...
Dear Sir or Madam,
I'm using a dev kit with the nRF52832 to realize a project in school. So my work contains two wearables and both include the nRF52832. Now I want to communicate...
Hello,
is it somehow possible to calculate the distance of a BLE enabled and advertising periodially cell phone to a turnstyle gate.
There are for example 10 turnstyle...
Hello,
I'm trying to update from Mesh SDK 1.0.0 to 1.0.1, I've followed http://infocenter.nordicsemi.com/topic/com.nordic.infocenter.meshsdk.v1.0.1/md_doc_getting_started_how_to_nordicSDK...
Hi all,
I would like someone give me a suggestion about timers.
in my current approvement I am using an RTC timer with 32k crystal to control my sleep times it is power...
