Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
So I'm basing this off of the ble_app_hrs that initially has heart rates service and battery service. I want to create my own custom service andcopied the project to use as...
Hello,
I tested the example project "custom serial chat" from Atmel and wanted to see which Handle is used to send and receive data from Smartphone to the BLE-Board (SAMD21...
Hi.
I am designing PCB based on NRF51822-QFAA-R7.
There is 2450BM14E0003T balun will be used.
Here is reference design for that pair (NRF51822 + 2450BM14E0003T):
www...
I would like to register a bug report with the nRF5 SDK version 12.2.0. If you look at the example code in the SDK you will find that every example has a different build configuration...
We have a project which need to control the distance between the slave and the master to be less than 10m, say 5m. We tried -20 and found it a little longer than we expected...
How can I trasfer 20bytes data per 10ms?
Currently, I set gap_conn_params.min_conn_interval 7.5ms, and use BLE_EVT_TX_COMPLETE to send data. However, Android APP nrf Connect...
[Aim]
I am working on a project where I aimed to Integrate/Develop firmware management system using Contiki running over Nordic NRF52.
[Components]
Contiki running over...
On a nRF52832...
I'm trying to create a DFU package to update an existing SDK 11 SD2.0.0 firmware, to update it to SDK 12 SD + new application + secure bootloader
But the...
Hi
I am using SDK 12.3.0 with softdevice s130 v2. When I try to combine ble_app_hrs_peripheral code with app_uart.c, uart module gives error NRF_DRV_UART_EVT_ERROR in uart_irq_handler...
I would like to use twenty concurrent connections. As I understand I should set ble_cfg.gap_cfg.role_count_cfg.periph_role_count = 20 and ble_cfg.conn_cfg.params.gap_conn_cfg...
Hello,
I have read with a lot of interest the documentation associated to the "multiprotocol support" associated to the nRF5 SDK for Thread v0.10.0.
As far as I understood...
This is a more specific counterpart to a question I posted on StackExchange . If you want to know more about the attack itself, check that out, but here, I'm asking for a...
Hello, please refer to the below code, in particular, did I get the cccd handle right?
static uint32_t mesh_value_char_add(void)
{
/* BLE GATT metadata */
ble_gatts_attr_md_t...
