I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello iam using softdevice 110 and SDK 10.0.0, I have created project using ble_app_uart example code, i have added device manager APIs to manage bonding. Problem is iam GATT...
Basically, it can be divided into two cases
Reading/sampling TX pin of the sensor (since usually nothing is sended back)
Send/Read possibility - in case of range switching...
Hi all, today I was working properly and, in a second my nRF52382 (I use SD s132 V3.0 without bootloader, and SDK 12.2) is "disappeared". I googled and I've found some cases...
I am using nrf51822 with 16k RAM chip, xAA.
I followed the procedures...but I don't know what is wrong with it..
Program secure bootloader with S130 (2.0.0), SDK...
Hello,
I am trying to use the new nRF Connect 2 for Desktop. After installation, the app gets stuck and doesn't show any GUI. Investigating the network shows that the app...
I have been setting up systems to develop nRF52 code for the better part of two years. Maybe I am getting forgetful in my old age, but I can't seem to get it working this...
Hi.
I am looking for appropriate 2.4Ghz Nordic RF chipset.
I have studied 2.4Ghz chipset. but so clearly show about
1:n audio streaming (mono or studio)
exactly what we...
Hi, we are using nrf51822 xxAB based module and would like to understand which SD/SDK combination is best to use in terms of memory usage. We have developed original firmware...
I'm in the process of migrating from SDK11 to SDK13. I have a custom UUID with 3 characteristics (2 notify chars for data and 1 r/w for sending commands), based off HRS and...
Using SDK 12.1.0
I2C with SoftDevice works on PCA10040 Eval Board with nRF52832 but
hangs in the nrf_drv_twi_enable function with TY module EBSGCNZWY which is an
nRF51822...
Attached program has 4 characteristics
UUID_VLEN1 - VLOC_STACK, no rd_auth or wr_auth - value can be read after written
UUID_VLEN2 - VLOC_USER, no rd_auth...
Hi guys,
I'm receiving the following errors whilst trying to setup to the Crypto library on nRF52:
............\components\libraries\svc\nrf_svc_function.h(72): error...
#problem
Not work ble sample code with s130 softdevice on nrf51822 module.
I just want to advertise by sample code.LED test with s130 is work well.
#Environment
...
Hi,
when looking at nrf_drv_i2s.c in SDK v13.0.0, the description of nrf_drv_i2s_start() states that the parameter buffer_size is Size of the buffers (in 32-bit words)...
