I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello,
is it possible to use the RSSI value of the NRF51822 for collision avoidance?
How long does an RSSI measurement take?
I'm trying to implement a discovery protocol...
Hi all! I used PWM module of nRF52832 to create the PWM but i don't know how to update new value to duty_cycle. This is my code. I used Button (Pin 13) to set a new DUTY_CYCLE...
I am trying to set custom value to advertising address. The code snippet is below. I am getting error code 0x10.
static ble_gap_addr_t * p_addr;
uint8_t itr_i;
p_addr...
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
We have a BLE application where we need hopping through nodes. I have shown below how it looks like. We don't want mesh network because we don't require node to node communication...
i use nrf52_DK to debug PDM with a digital MIC, and select the P0.09 for the PDM clk, but i have not see any clock signal output, is it right? and i also haven't see the convet...
Say I have 3 records, then I delete them and collect the garbage. If I try to save a new record again, it will be saved with a record ID 4 , but it should be back to 1 after...
I want to use the development kit for Bluetooth 5.0 IoT product development.
Is there already a bluetooth mesh software available for the nRF52840 development kit?
Or...
I am working on time synchronizations between different nodes in a mesh network. I have earlier worked on the radio and the ppi examples given. I wish to generate time stamps...
Hi
I would like to prepare a provisioning hex file for my firmware.
Can somebody supply an example how this could be made?
I'm using gcc toolchain, Eclipse and SDK...
Hello,
I am using sdk12.2.0 and pca10028 dk. I am using one code downloaded from unknown source. The code is used to store data in flash. When I compile through keil I don...
Hi,
i try to establish a communication between 3 sensors in the following way!
Node 1 should broadcast messages to Node 2 and Node 3 as Peripheral.
To establish a...
Hello,
I am using pca10028 and sdk 12.2. I have interfaced temp sensor with nrf51 and now I want to store that data continuously in memory of nrf51. I want to store min 4k...
Hello, I want to program and debug the nrf52840 device but I'm kind of stuck at the programing range/address issue.
I'm using my customized board so I doubt Nordic Semi...
