Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
I'm having difficulties writing, retrieving and deleting data from flash, using fds on nRF52832_XXAA. Sometimes the flash writing succeeds, sometimes it fails with with ret_code_t...
I want to know about some range information of the NRF52 & NRF21 (BEACON).
For example if I have TX power of the beacon +4 dBm and which is broadcasting every 500 ms so...
Hi all,
I tried to build the latest OpenThread libraries but after copying the library files in the SDK, I fail to compile the examples. Everything was fine when building...
Hello,
the specification states that SD132 v4 takes 120 KB flash and MBR 4 KB flash additionally. We only need the BLE protocol stack. Is there any way to reduce the SD132...
I am trying to use the EVENTS_PWMPERIODEND interrupt to read a GPIO pin on every falling edge of an output GPIO that is driven from the PWM module.
The description in the...
Hi all,
i developer a code that :
press button short switch on one led
Press button long switch on two led.
but sometimes if i press the button a two led...
hi
i need store my data in internal flash memory (around 30kb). i have fixed memory map from 0x25000 to 0x35000. my,
block size = 16 byte,
block count =4096,
no of pages...
Hi,
I want to add functions of HID telephony to pickup/decline phone on nrf51822 application.
But it seems telephony usage did not work on android/ios phone, or incorrect...
hi :
I use Gzll protocol to realize 2.4G frequency hopping communication， One Device send data to One Host on Pipe2 receive. Now I use nrf24lu as "Host" and nrf51822 as ...
Hello,
My rigado BMD 200 board suddenly stopped responding. the Jlink interface cannot connect
I tried nrfjprog --recover with no success.(says cannot connect)
in segger...
I am using nrf51822 with sdk 6. I was using double bank ble dfu for the firmware upgrade. But now I have to switch to single bank dfu since my code size has exceeded the maximum...
hi ，
image 1 、
image 2、
image 3、
I now use nRF24LU1P for Bootloader upgrade, using the routine is the official website of the C# Lu1BootLdrTest project, nRF24LU1P...
Hi,
I have a nrf24lu1p usb dongle by hand and I want to know the flash size.The package marking is:
nRF D
LU1P16
1219AC
I am not sure whether the chip has a 16kB flash...
Based on multi-protocol add private agreement GZLL matching procedure, no matching success;But separate GZLL agreement can be successful, not any way to solve this problem...
Hey devs!
We'd like to add additional fields in the manifest.json when generating (or after generating) the zip file for DFU. We need these fields to make additional compatibility...
