Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hello,
I am using S110 8.0 soft device and using the example Nordic_UART. I am able to compile the project file in KEIL and flash it onto my board. I don't see any errors...
We are using the low power comparator on NRF51882 RayTac Module (Vcc=3.3V, Vref = 4/8), with which we are making a precise high impedance measurement!
I found some documentation...
I've been sending various BLE addresses to the nRF51 and am getting some inconsistencies of what addresses are being deemed valid.
I am using BLE_GAP_ADDR_TYPE_RANDOM_STATIC...
I am using uVision 5.18a with MDK-Lite ARM toolchain and I downloaded nRF examples for SDK 11.0.0-2.alpha with Pack Installer.
Then I tried to compile " /ble_peripheral...
Hello everyone,
I would like to know, if it is possible to send data (power data) from a NRF52-DK to a Garmin Display Device. Do you know any application, project example...
I wanted extract BLE_GAP_AD_TYPE_128BIT_SERVICE_UUID_COMPLETE that i receive while scanning and compare it with 128 bit service uuid that i defined.
i have seen how ot...
Hi,
I am trying to debug my code in Eclipse using J-Link.
Whenever the code executes vPortStartFirstTask() in vTaskStartScheduler() the debugger stops and I can't debug...
Hi,
is there any simple way to obtain current PWM value if nrf52 PWM module is used to produce complex waveform from RAM array? The task is to get currently settled value...
Hi there,
I am new with nRF52 using SD332 and ANT+. I would like to ask if the nrF52 with SD332 can be configured as ANT+ central and ANT+ peripheral in the same time....
I have a query that is similar to the question below
https://devzone.nordicsemi.com/question/44424/how-do-i-switch-the-target-from-a-nrf51422_xxac-to-nrf51422_xxab-in-keil...
Hi,
We are currently considering the packaging design of a device which will use a nRF52. During housing assembly, the populated, but unpowered, PCB will be exposed to...
Hello.
I have a question.
I use nRF52 and S132v2. I found some programs of nRF51, they use S110, S130. What change does it with difference of Softdevice's version number...
Hi,I am working on Eddystone project i.e nrf5-sdk-for-eddystone-master and tested it on NRF52(PCA10040) development board it advertising Eddystone-URL frame successfully and...
hi
i have nrf51422 v2 that use sdk v6 and s210 v3
when i download an example on my nrf and run it to see error check its not returning anything
in s110 i have error...
Hi, In my custom project I need to add two 128-bit uuid services and also I need to use pstorage to protect the application data from power loss. But I got the problem is...
